Cricket Ball Trajectory: Swing, Spin, Bounce and the Delivery That Hits the Stumps

Bowl a 156.5 g ball on a Blender cricket ground: drag, Magnus force, swing, a rigid-sphere bounce with friction, and a solver that lands it where you aim.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A regulation cricket ball (156.5 g, radius 35.6 mm) is released at 2.2 m height and 0.7 m in front of the bowling crease. The page solves for the launch elevation and direction that make the ball land exactly on the spot you choose (length and line), flies it through the air with gravity, drag, a Magnus force from its spin and an adjustable swing force, bounces it off the pitch as a rigid sphere with friction, and carries on to the batter's stumps 20.12 m from the bowler's stumps. The stumps fall if the ball centre comes within one ball radius plus a stump radius of one of them below 711 mm.

Equations

  • Motion: m a = −CD q v̂ + CL(S) q (ω̂ × v̂) + Csw s q x̂ + m g with the dynamic pressure times area q = ½ ρ A v², ρ = 1.2 kg/m³, A = π R², CD = 0.45. Integrated with fourth-order Runge-Kutta, 2 ms steps.
  • Magnus lift coefficient against the spin parameter S = R ω / v: CL = 1.6 S / (1 + 3 S), a saturating fit that is linear at small spin (the usual slope for sports balls).
  • Swing: a sideways force Csw s q with Csw = 0.15 and the slider s from −1 to 1. Real swing comes from the polished and rough sides of the ball separating the air at different places; no simple law gives its size, so the number is a representative value set by the slider.
  • Bounce (surface normal up, a solid sphere with I = (2/5) m R²): the vertical speed becomes e times the incoming vertical speed, the normal impulse is Jn = m (1 + e) vn, and the contact point moves with u = v + ω × rc. If the impulse needed to stop the contact point, m |u| / 3.5, is below μ Jn the ball grips; otherwise it slides and the friction impulse is μ Jn. Both change the sideways speed and the spin.
  • Seam kick: a lateral impulse κ sin(τ) Jn on the bounce, where τ is the tilt of the spin axis. This is an empirical stand-in for the ball landing on its seam.
  • Aiming: Newton's method on the elevation and azimuth angles, with a finite-difference Jacobian, until the first touchdown is within 10 μm of the chosen spot.

Checks run in the page

  • With drag, Magnus and swing off, the first touchdown against the closed-form parabola.
  • A ball dropped with only air drag: the speed after 3 s against the exact tanh solution.
  • Rigid-sphere bounce: angular momentum about the contact point is unchanged (gripping and sliding case), vertical speed is e times the incoming one, and a gripping bounce leaves the contact point at rest.
  • The aiming solver reaches three target spots to within a millimetre in an independent finer integration.
  • Magnus force alone: the sideways drift after 0.2 s against the constant-force estimate.

Honest simplifications

  • The drag coefficient is a constant; in reality it changes with speed and with which way the seam faces (that change is what makes real swing). The Magnus fit and the swing force size are illustrative, not measured on a cricket ball.
  • The spin rate is constant in flight and the spin axis does not precess; the seam position is only drawn from the spin.
  • The pitch is a flat rigid surface with one restitution and one friction value; a real pitch is softer, cracks, and its bounce depends on moisture and wear. Rolling resistance, a second bounce and the ball hitting the stumps are not modelled beyond the bowled/not-bowled decision, and the batter is not included.
  • Release height and point are fixed; real bowlers vary them. There is no wind and no humidity effect.
  • The stumps' fall and the bails flying are animation only.

What to try

  • Set swing and spin to zero (last preset) and note the bounce spot and the angle at which the ball leaves the pitch.
  • Switch to the off-spinner preset: slow, much spin and a strong grip, so the sideways kick at the bounce is large while the flight stays almost straight.
  • Raise the pitch friction and watch the ball switch from sliding to gripping.
  • Slow the time scale to 0.05 and follow the ball through the bounce.
Loading model...
Loading Blender model...
Top view of the delivery
Side view of the delivery
Magnus lift coefficient against spin parameter
Made with 🟠 Blender · Three.js