3D Kite Flight: Lift, Drag, Line Tension and the Minimum Wind to Fly

Fly a diamond kite on a Blender-built field: flat-plate lift and drag, a bridle that sets the angle of attack, gusts, a taut line and a balance solver.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A diamond kite (1.0 m x 1.2 m, 0.6 m²) on a straight line held at hand height, flying in a vertical plane with the wind along the ground. The kite is treated as a point mass whose sail sits at a fixed bridle angle to the line, so its angle of attack changes by itself as it climbs or sinks. Wind, gusts, line length, bridle, mass, area and tail drag are all adjustable; the tension and elevation you read are results of the integration, not animations.

Equations

  • Kite at position (x, z) from the hand, line elevation ε = atan2(z, x). The bridle fixes the sum γ = χ + ε of sail pitch χ and elevation, so climbing lowers the angle of attack (a restoring effect).
  • Apparent wind vr = (w − vx, −vz), dynamic pressure q = ½ ρ |vr|² S with ρ = 1.225 kg/m³.
  • Sail force: a thin flat plate with normal-force coefficient CN = 2π sinα / (4 + π sinα), acting along the sail normal, plus a form drag CD0 + Ctail (0.05 + your tail setting) along the apparent wind. Lift and drag follow by projecting this force perpendicular and parallel to the apparent wind.
  • Motion: m a = Faero + m g. The line is a rigid constraint r ≤ L; when taut, the tension is T = m ar + m vt²/L, with the radial acceleration including gravity. When the line goes slack the kite flies freely.
  • Steady balance: with the kite at rest the force across the line vanishes, −sinε Fx + cosε (Fz − m g) = 0; the page solves this by bisection and shows the elevation, tension and the minimum wind for which a flying balance exists.
  • Optional shear: w(z) = w10 (z/10 m)1/7. Gusts multiply the mean wind by 1 + g (0.5 sin 0.9t + 0.3 sin(2.3t+1) + 0.2 sin(5.1t+2)) (a repeatable stand-in for turbulence).
  • The drawn line sags by the parabola wl L² / (8T) with 1 g/m line weight; the sag is for the picture only and does not feed back into the physics.

Checks run in the page

  • Balance elevation by bisection against the elevation the time-stepped flight settles to by itself.
  • Tension at rest from the balance solver against the constraint force of the stepped flight.
  • Free fall of 2 s against 100 − g t²/2 (integrator exactness).
  • The taut line as a pendulum with air off: period against 2π√(L/g).
  • Doubling the wind multiplies tension by 4 and leaves the elevation unchanged when the weight is removed.

Honest simplifications

  • Motion is restricted to the vertical plane through the wind. Real kites also move sideways and rotate; the bridle makes the pitch follow the line direction instantly, so pitch oscillations and stalls of the kite as a body are not modelled.
  • The flat-plate coefficient law is an empirical fit, not a measurement of a cloth sail; real sails billow, so lift and drag differ by tens of percent. The extra drag of tail and frame (0.05 + slider) is representative, not measured.
  • The line has no aerodynamic drag, stretch or elastic energy (the sag drawn in the picture is visual only), and a gust acts on the whole kite at once with no spatial structure.
  • The tail ribbons and the windsock motion are cosmetic. The windsock is not a calibrated instrument.
  • Ground contact is a simple floor 0.5 m above the grass with a little sliding friction.

What to try

  • Lower the wind in steps and read the minimum wind needed to fly; below it the kite stays on the ground.
  • Raise the bridle angle: the sail meets the wind at a smaller angle of attack and the kite flies lower, at a higher tension per square metre.
  • Switch on the wind shear and see the kite settle higher, where the wind is stronger.
  • Set gusts to 0.5 and watch the tension graph spike while the elevation hardly changes.
Loading model...
Loading Blender model...
Line tension against time (and the steady-wind balance)
Side view: the kite path and the line-length circle
Lift and drag coefficients against angle of attack
Made with 🟠 Blender · Three.js