3D Turbofan Jet Engine: Brayton Cycle, Thrust and Efficiency

A cutaway two-spool turbofan: ISA atmosphere, compressor and turbine matching, fuel flow, thrust, TSFC and efficiencies from altitude and Mach number.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A two-spool high-bypass turbofan on a test stand. A fan driven by the low-pressure turbine pushes air through two paths: most of it goes round the core (the bypass stream) and a smaller part is compressed further, burns fuel in the combustor and drives the turbines. The page follows one kilogram of core air station by station and then adds up the momentum of both jets.

Equations

  • Ambient air follows the International Standard Atmosphere: T = 288.15 − 6.5 h (h in km, up to 11 km), p = 101325 (T/288.15)5.2559. Flight adds ram compression: Tt0 = T0(1 + 0.2 M²), pt0 = p0(Tt0/T0)3.5.
  • A compressor with pressure ratio π and isentropic efficiency ηc heats the air to Tt,out = Tt,in [1 + (π(γ−1)/γ − 1)/ηc].
  • Combustor energy balance: cp,h(1 + f) Tt4 = cp,c Tt3 + ηb f LHV, which gives the fuel-air ratio f for the chosen turbine inlet temperature.
  • Shaft balances: the high-pressure turbine supplies exactly the core compressor work, the low-pressure turbine supplies the fan work for the whole airflow, (1 + f) cp,h ΔTLPT ηm = (1 + BPR) cp,c ΔTfan. Each turbine's pressure drop follows from πt = [1 − ΔTt/(ηt Tt)]γ/(γ−1).
  • Jets expand to ambient pressure: V = √(2 cp ηn Tt [1 − (p0/pt)(γ−1)/γ]). Thrust is F = ṁc[(1+f)Vc − V0] + ṁb[Vb − V0], and TSFC = ṁf/F.
  • Efficiencies: thermal ηth = ΔKE/(ṁf LHV), propulsive ηp = F V0/ΔKE, overall ηo = ηthηp. For one jet, ηp = 2V0/(V0 + Vj), which is why a big, slow bypass stream saves fuel.
  • Spool speed shown on the readout: tip speed U = √(cp ΔT / ψ) with a stage loading ψ of 0.4, divided by the radius. The turbine inlet temperature follows the throttle with a 2.5 s time constant.

Checks run in the page

  • The standard atmosphere is compared with tabulated values at 0, 11 and 15 km.
  • A loss-free cycle (all efficiencies 1, no bypass) must reproduce the closed-form Brayton efficiency 1 − r−(γ−1)/γ from the jet kinetic-energy accounting.
  • A loss-free single jet at Mach 0.8 must reproduce the Froude propulsive efficiency, and the low-pressure turbine power must equal the fan power in the real case.

Honest simplifications

  • Constant specific heats (1004.5 J/kg/K cold, 1156 hot), no turbine cooling air bleed, no real compressor maps, surge, choking or off-design matching: the flow is set by a corrected-flow number, not by blade geometry.
  • Nozzles are fully expanded and the fuel is treated as a plain energy source. Real engines lose a few percent more to bleed air, leakage and installation.
  • The Blender model shows the layout (fan, three low-pressure and six high-pressure compressor stages, annular combustor, high-pressure and low-pressure turbine) but is not a specific commercial engine. The airflow and exhaust are illustrations, not a CFD solution. Rotor speed on screen is slowed down by the slider; the readout shows the true rpm.

What to try

  • Choose the preset Old turbojet, then Geared ultra-high bypass: the thrust per kg of air falls, but TSFC drops by more than half.
  • At cruise (11 km, Mach 0.8) watch thrust fall to a fraction of the take-off value while the propulsive efficiency rises.
  • Raise the turbine inlet temperature at a fixed overall pressure ratio and compare thrust gain to the extra fuel.
  • Raise the bypass ratio to 12 with a low fan pressure ratio until the cycle status reports that the turbines cannot drive the fan.
Loading model...
Loading Blender model...
Temperature-entropy diagram of the core stream (real vs ideal)
Thrust and TSFC vs flight Mach number
Thrust and TSFC vs bypass ratio
Made with 🟠 Blender · Three.js