Presets
Playback
Parameters
Camera
Layers
Quality
Model check
The science
What is modelled
One escalator: a 4.2 m rise at 30 degrees, a closed chain of steps that stay horizontal on the carrying run and flip over on the two sprockets, and a motor with a gearbox and a brake. Passengers board at the entry as steps pass, the model adds up the gravity, friction and inertia forces on the chain, and reports shaft power, grid power (motoring or overhauling), capacity, the speed ripple caused by the sprocket teeth and the stopping distance.
Equations
- Track: flat
Lf, concave arcrc, inclineLi = [H − (rc + rv)(1 − cos 30°)]/sin 30°, convex arcrv, flatLf; the return run is the same curve 2Rt lower. Chain lengthLt = 2Lc + 2πRtwithRt = plink/(2 sin(π/z)), z = 24 teeth. - Capacity (EN 115 form):
C = 3600 v k / 0.4persons per hour,k= 1.0, 0.75, 0.5 for 1000, 800, 600 mm steps. The model counts boardings with the real step pitchp = Lt/N. - Drive force on the chain:
F = ∑i mi g sin hi + M a + crr g ∑i mi |cos hi| + F0 + Fhandrailwherehiis the track heading at step i. PowerP = F v; grid power divides by the drive efficiency (0.85) when motoring. - Empty steps cancel: the weight of steps climbing on the carrying run is balanced by the same number descending on the return run, so only passengers load the drive. A loaded descending escalator has
P < 0: the passengers drive the motor (overhauling) and the brake or a regenerative drive must absorb it. - Polygon effect: link speed on the straight run is
ω Rs cos βwithβbetween −π/z and π/z, sovmax/vmin = 1/cos(π/z)(0.86 % for 24 teeth, 3.5 % for 12). - Stopping: constant deceleration, distance
v²/(2a), timev/a; EN 115 requires 0.20 to 1.00 m at 0.5 m/s.
Checks run in the page
- The sampled track polyline equals the closed-form chain length, the carrying run rises exactly 4.2 m and the loop closes.
- Boardings counted in a 120 s run with a permanent queue equal 3600 v k / p.
- The sum of m g v sin(heading) over passengers on the curved track averages to flow x m g H; the empty steps have almost no net gravity pull.
- The sampled link-speed swing equals 1/cos(π/z).
- Integrated braking distance and time equal v²/2a and v/a and lie inside the EN 115 band.
Honest simplifications
- Each passenger is a 75 kg point mass standing in the middle of a step; no luggage, children or sway. Boarding is a smooth fluid queue (arrival rate in persons per minute), not individual walking.
- Step mass 32 kg, rolling resistance, chain and handrail drag (250 N and 220 N) and the 85 % drive efficiency are illustrative round numbers, not those of a product. Real escalators also use a variable-frequency drive, step-chain tension carriage and many safety switches that are not modelled.
- The handrail is shown only as moving markers; its own drive and friction are lumped into the 220 N term. The deceleration is commanded; the brake torque needed is not computed.
- This model is independent of any manufacturer and standard values are quoted only as sanity bands.
What to try
- Press Direction to send the staircase down at full flow with regeneration off: shaft power turns negative and energy goes into the braking resistor; switch regeneration on to see grid power go negative.
- Set the arrival rate above the capacity and watch the queue grow while the boarding rate stays at the capacity line in graph 3.
- Choose 600 mm steps: capacity halves at the same speed.
- Press Stop at different deceleration values and compare the measured distance with v²/2a.
Loading model...
Loading Blender model...