Steam Locomotive: Tractive Effort, Adhesion, Boiler Steam Supply and Gradient

A goods locomotive on a 6 km loop with a hill: cylinder work per wheel turn, adhesion limit, steam supply, resistance and braking.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A goods steam locomotive (0-6-0 with a tender) hauling up to twelve coaches round a 6 km loop with a 1.5 % climb and a 1.0 % descent. You drive it with the regulator (throttle), the reverser (cut-off) and the brake, and watch the tractive effort, the adhesion limit, the boiler pressure and the steam supply decide how fast the train can go. The wheels, connecting rod, coupling rod and crosshead are driven by the real crank geometry.

Equations

  • Work of the cylinders per wheel revolution (two double-acting cylinders, admission pressure pa = regulator × pboiler, cut-off c): per face W = pa(Vc − V0) + (paVc − pxVe)/(n − 1) − pe(Ve − V0), with px = pa(Vc/Ve)n. Tractive effort F = W/(πD) (work per revolution divided by the distance rolled).
  • Adhesion: the wheels grip while F ≤ μ mad g; beyond it they slip and the force drops to 0.7 of the limit.
  • Resistance: R = cr M g + ½ ρ CdA v²; gradient force M g sinθ; train equation Me dv/dt = F − R − M g sinθ − Fbrake with Me = 1.04 M (rotating parts).
  • Boiler: steam used per second = steam per wheel revolution × revolutions per second; the stored steam changes as Cb dp/dt = mgen − muse (about 55 kg per bar for a 5 m³ water space); coal is 0.13 kg per kg of steam. The safety valve opens at 10.5 bar gauge.
  • With the supply limit the sustained force falls as F = mgen (W/mrev)/v, a constant-power hyperbola (purple dashed in the second graph).
  • Exhaust beats: four per wheel revolution (two cylinders, two exhausts each), which is the chuff rate shown.

Checks run in the page

  • Terminal speed on the level, uphill and downhill against a bisection of the force balance.
  • Coast-down with the regulator shut against the exact tangent solution of the drag equation.
  • Rod geometry (rod length constant, crosshead travel = stroke) and the four beats per wheel turn.
  • The steam ledger of the boiler and the brake stopping distance against the closed form.

Honest simplifications

  • The cylinder cycle is the idealised one from the steam-engine model: no compression, lead, wall condensation or valve-gear detail, and a single polytropic exponent. The factor 1/(1+(v/20)²) that reduces the force at speed stands in for port and steam-chest losses and is an illustrative curve, not a measurement.
  • Rolling resistance (0.25 %), the drag area (9 m²), masses and boiler size are typical illustrative values, not a specific locomotive. Curves, wind, brake adhesion, rail wetness changes and water level are not modelled; the train cannot roll backwards.
  • The gradient is shown tilted four times steeper than real so that it is visible. The cylinders on the far side are not drawn.

What to try

  • "Heavy train, dry rail" on the 1.5 % climb: the speed falls until the force balances the gradient.
  • "Wet rail: wheel slip": the cylinder force exceeds the adhesion limit and the drivers spin.
  • "Weak fire": the boiler pressure sags while the steam use exceeds the generation.
  • Switch on cruise control and watch the regulator open on the hill.
Loading model...
Loading Blender model...
Track elevation profile of the 6 km loop and the train position
Tractive effort diagram: cylinder, adhesion and steam limits against resistance
Speed and boiler pressure against time
Made with 🟠 Blender · Three.js