Bucket-Wheel Excavator: Chip Thickness, Bucket Fill, Belt Capacity and Power

A Blender-built bucket-wheel excavator cuts a lignite bench layer by layer: swing speed sets the chip, bucket fill and belt capacity set the limit, and the specific cutting energy sets the power.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A bucket-wheel excavator working a lignite bench. The wheel (10 buckets of 0.9 m³, radius 4.95 m) turns at the end of a boom; the whole superstructure slews sideways so the buckets shave slices off the face, one layer per swing, the boom is lowered between swings, and the coal runs on a belt up the boom and out along the discharge boom to a stockpile. You set the swing speed, bucket speed, cut depth, layer height, hardness and swell; the page works out the chip thickness, the bucket fill, the throughput, the belt load and the power of the wheel, and what limits the machine.

Equations

  • Wheel speed n = vt / (2π R), buckets passing the cut per second z n.
  • Swinging sideways at vs removes a bank volume rate Q = vs a Hc (cut depth times layer height times swing speed); each bucket takes a slice of thickness h = vs / (z n).
  • Loose volume Ql = s Q (swell factor s). Bucket fill kf = Ql / (z n Vb); the belt can carry A v loose volume per second. The limiter reduces the swing speed so that the fill stays at or below 90 % and the belt is not overloaded.
  • Cutting power from the specific cutting resistance: Pcut = kc Q (kc in kN/m² = kJ/m³). Lifting power Plift = ρ Q g hlift with the bucket lifted from the cut to the chute, hlift = R (1 + cos 15°). Drive losses are 15 % of the sum.
  • Belt: mass flow ṁ = ρ Q, load per metre ṁ/vbelt.

Checks run in the page

  • Cutting a terrace layer by layer: the volume removed from the 64 bench columns equals arc x depth x height and the time integral of vs a Hc.
  • Bucket passes counted over 600 s against z n t and chip thickness times passes against the swing distance.
  • Conveyor mass balance and the steady belt load.
  • Per-bucket cutting forces summed over one revolution against the specific-energy power.

Honest simplifications

  • The cut is a clean block cut with a constant chip thickness; the real chip is sickle-shaped, bucket filling is not complete at the start of a pass, and boulders, hard bands and water change the resistance. The specific cutting resistance kc is an input (typical lignite values are 100 to 300 kN/m²), not computed from the material.
  • Power covers the wheel only: slewing, boom luffing, travel, belts and idle running are not included, so the specific energy is lower than a whole-machine figure.
  • The belt is a one-dimensional conveyor with a donor-cell scheme (it smears the leading edge); the discharge heap is a row of columns, not a repose-angle pile.
  • The machine sizes (wheel radius, 10 buckets, 0.9 m³ each, a 1.8 m belt at 5.2 m/s) are typical of a mid-size machine, not a particular model, and time is sped up by the time-scale slider.

What to try

  • Raise the swing speed to 0.45 m/s: the limiter caps the machine at the bucket-fill limit and the page names it.
  • Switch the limiter off and watch the bucket fill pass 100 per cent, the point where coal spills.
  • Choose the Hard, sandy lignite preset: the cutting power grows in proportion to kc.
  • Choose Deep cut: now the belt, not the buckets, limits the throughput.
Loading model...
Loading Blender model...
Bank throughput against swing speed
Wheel power against swing speed
Mined volume against time
Made with 🟠 Blender · Three.js