Wind Turbine Aerodynamics 2D

Blade element momentum solver: stream tube, velocity triangle, stall, power curve and pitch control of a 2.5 MW rotor.

Presets

Playback

Layers

Model checks

The science

How much of the wind can a rotor take?

A rotor of radius R sweeps the area A = πR2. The kinetic power flowing through it is Pwind = ½ ρ A U3, so doubling the wind gives eight times the power and doubling the radius four times. The power coefficient Cp = P / Pwind measures how much the machine extracts. In one-dimensional momentum theory the rotor slows the wind to U(1 − a) at the disc and U(1 − 2a) far downstream, where a is the axial induction factor. Thrust and power are CT = 4a(1 − a) and Cp = 4a(1 − a)2; the maximum of the second is at a = 1/3 and equals 16/27 = 0.593, the Betz limit. The stream-tube picture in the 2D view widens exactly as continuity demands, A(x) u(x) = const.

Blade element momentum (BEM) theory

Real blades also spin the wake. Cut each blade into annular elements at radius r. The air meets an element with the relative velocity W, made of the axial part U(1 − a) and the tangential part Ωr(1 + a′), where a′ is the tangential induction. The inflow angle is φ = atan[ U(1 − a) / (Ωr(1 + a′)) ] and the angle of attack is α = φ − θ, where θ is the section pitch (built-in twist plus the collective pitch you set). The airfoil gives Cl(α) and Cd(α), which are projected on the axial and tangential directions:

Cn = Cl cosφ + Cd sinφ, Ct = Cl sinφ − Cd cosφ, dT = ½ρW2 B c Cn dr, dQ = ½ρW2 B c Ct r dr.

The same annulus must also satisfy momentum theory, dT = 4πrρU2a(1 − a)F dr and dQ = 4πr3ρU(1 − a)a′ΩF dr. Equating the two descriptions gives a and a′, found by iteration at every element (24 elements from 15 % of the radius to the tip). F is Prandtl’s tip and hub loss factor, which accounts for the finite number of blades B. For heavily loaded elements (CT > 0.96F) the Buhl empirical correction replaces the momentum relation. Finally P = Ω ∫ dQ and Cp = P / (½ρπR2U3).

Tip-speed ratio and stall

The tip-speed ratio is λ = ΩR / U. For a fixed blade, λ sets every inflow angle. At low λ the angle of attack exceeds the stall angle (14° in this model): lift collapses, drag soars and Cp drops (use the preset “Too slow”). At very high λ the angle of attack goes to zero, there is no lift to speak of and Cp falls again (“Too fast”). The optimum, near λ = 6.6 for this blade, is where the whole blade works near its design angle of 10° (third graph). The blade shape is the optimal one for 3 blades: c ≈ 8πr(1 − cosφd) / (B Cl,d) with φd = (2/3) atan(1/λdx) and the twist φd − αd (limited near the root).

Control: from cut-in to cut-out

Below rated wind speed the controller adjusts the rotor speed so that λ stays at the optimum (maximum power point tracking). Above rated power (2.5 MW at R = 40 m, scaled with R2) the blades are pitched to reduce the angle of attack, which keeps the power constant while cutting Cp and the loads; above 25 m/s the machine parks. Because P ∝ U3 the power curve rises steeply until rated and then flattens. Yaw error reduces the normal wind to U cosγ (a first approximation; measured losses are close to cos2).

Three in-page numerical checks

1. A scan of 4a(1 − a)2 finds the maximum 16/27 at a = 1/3, and the full BEM rotor with the drag and tip losses switched off at the design point must fall just below it (about 0.57 because of the finite hub and the cut root). 2. In every converged element with a < 0.38 the blade-element thrust equals the momentum-theory thrust, and the blade-element torque equals the angular-momentum torque (relative error below 10-4). 3. The live operating point never exceeds the Betz limit.

Honest simplifications

The airfoil polar is an analytic model (linear lift with slope 5.9 per radian, a smooth transition to flat-plate behaviour after 14°, a parabolic drag polar), not wind-tunnel data; there is no dynamic stall, no 3D stall delay, no tower shadow, no wind shear or yaw dynamics, and no blade elasticity. The rotor speed follows the controller set-point through a first-order lag instead of integrating a torque balance with generator torque. The 3D page uses the same solver; its landscape and the animated flow are illustrative.

What to try
  • Press Rated wind 12 m/s and then raise the wind slowly: the power curve (first graph) flattens at 2.5 MW while the pitch angle rises.
  • Choose Manual tip-speed ratio and drag the ratio from 3 to 13. Watch the dot slide along the Cp curve, and the third graph show the angle of attack hit the red stall line for low ratios.
  • Preset Too slow: the blade turns red in the front view; drag at the probe radius rises in the velocity triangle.
  • Move the Probe radius slider: the section near the tip moves much faster than the root, so the same wind makes a much flatter inflow angle there.
  • Raise the Yaw error to 40 degrees and read how much power is lost.
  • Compare 2, 3 and 4 blades: more blades raise the maximum Cp a little (smaller tip loss) but the cost goes up faster than the gain.
  • Press Gust +50% and see the stream tube and the controller react.
  • Preset Thin air at 3000 m: the same turbine produces about 26 % less power because P is proportional to the air density.
Starting...
Power curve of this turbine and the Betz limit
Power coefficient Cp against tip-speed ratio
Angle of attack along the blade