Presets
Playback
Fork A (and B: same geometry)
Fork B and the table
Excitation
Time
Layers
Model check
The science
What you are looking at
Two metal tuning forks stand on a table. Fork A is struck (or driven by a tone generator); fork B is its neighbour. Each fork is modelled by its fundamental bending mode as one damped oscillator, and the two oscillators are coupled weakly through the table. A resonance box under a fork makes it louder but makes it ring for a shorter time.
Why a fork has a pitch: the cantilever
Each prong is a beam clamped at the stem. For a uniform beam (Euler-Bernoulli theory) the fundamental frequency is f = (beta^2 / 2 pi) (a / L^2) sqrt(E / 12 rho) with beta L = 1.8751 the first root of cos(beta L) cosh(beta L) = -1, prong length L, thickness a in the bending direction, Young's modulus E and density rho. The default (steel, L = 100 mm, a = 5.4 mm) gives 440 Hz, concert A. Doubling the length lowers the pitch by a factor of four. The overtone is 6.27 times higher, which is why a fork sounds almost pure: the first overtone dies out quickly and the plain fundamental is what you hear.
Resonance and ring-down
The oscillator is x'' + (w/Q) x' + w^2 x = w^2 x_s cos(w_d t). Struck, it decays as exp(-t / tau) with tau = Q / (pi f). Driven at its own frequency, the steady amplitude is Q x_s: a push of one micrometre becomes several millimetres. The width of the resonance peak is f / Q, so a high-Q fork responds only to an almost exact match.
Sympathetic resonance and beats
The table adds a coupling stiffness k_c = c k between the two modal coordinates (the distance dependence of c here is a stylised law, not a measurement). Two identical forks then have two normal modes: both swinging together (frequency f) and in opposition (f sqrt(1 + 2c)). Striking A excites both, and the energy slowly moves between the forks with first full hand-over after pi / (w_a - w_s). If B is slightly mistuned by a clip, only part of the energy transfers and the pitches beat at the difference frequency. The clip changes the frequency as f' = f / sqrt(1 + M / (0.2357 m)) where m is the prong mass.
Numerical checks on this page
- A finite-element cantilever (30 Hermite beam elements, inverse iteration) gives
(beta L)^2 = 3.5160and the overtone ratio 6.267, and the fork frequency computed from it is compared with the closed-form formula. - The ring-down time of an isolated simulated fork is measured from two amplitudes and compared with
Q / (pi f). - For two identical forks the simulated time of the first complete energy transfer is compared with
pi / (w_a - w_s). - The driven steady-state amplitudes from the time integration are compared with the closed-form complex solution of the 2 by 2 linear system.
What is simplified
Each fork is reduced to its fundamental mode; the real prongs also have the stem motion and a small second-harmonic content when struck. Both prongs move exactly in opposition (no net force on the stem), so the coupling is a lumped, symmetric effect; the two forks have the same modal mass. The resonance-box factors (Q divided by five, louder sound) are illustrative, not acoustic measurements. Amplitude is the tip displacement; the dB levels are relative to 1 mm, not sound-pressure levels. Sound output (Web Audio) plays the two fundamental frequencies with gains following the simulated amplitudes, at real time speed.
What to try
- Strike A with the default settings: B starts to ring a little later, then the energy returns.
- Put a 0.12 g clip on B: the forks now beat; turn on Sound to hear it.
- Choose the sweep preset and watch the measured dots follow the closed-form resonance curve.
- Lower Q to 500 or add boxes and see the wider peak and shorter ring.
- Switch the material: steel and aluminium nearly share a pitch because the speed of sound in them is about the same.