Glacier calving front: crevasses, meltwater and flotation

Nye crevasse depth, water-filled crevasses, flotation and a calved berg that floats or capsizes.

Switch to 2D

Presets

Playback

Glacier and fjord

Run

Camera

Layers

Quality

Model check

The science

What is modelled

A tidewater glacier front: a slab of ice of thickness H ending in a vertical face in a fjord of depth dsea. The ice stretches along flow, so surface crevasses open; meltwater fills them and can drive them down to the waterline, where a block breaks off. It is a one-dimensional teaching model (one crevasse, one strain rate) and all defaults are illustrative, not a forecast for any real glacier.

Equations

  • Glen's flow law, n = 3: ε̇ = A τn. The rate factor follows an Arrhenius law from A(0 °C) = 2.4×10−24 Pa−3 s−1 (approximate activation energy 80 kJ/mol, a typical value).
  • Nye (1957) resistive stress Rxx = 2 (ε̇/A)1/n and dry crevasse depth d = Rxx/(ρi g). Doubling the strain rate deepens the crevasse only by 21/3.
  • Water-filled crevasse (Benn et al. 2007): d = Rxx/(ρi g) + (ρw/ρi) dw. Calving when d reaches the freeboard, so the critical water depth is dw* = (ρi/ρw)(hfree − ddry).
  • Flotation: Hf = (ρw/ρi) dsea; height above buoyancy Hab = H − Hf. A basal crevasse rises hb = ρi/(ρw−ρi) (Rxx/(ρi g) − Hab) where tension exceeds Hab; surface plus basal crevasse spanning H also calves.
  • Time stepping: the crevasse fills at (melt − drain) m/day, the front advances at the ice speed, each calving removes Lc of front and empties the crevasse (step 0.05 d). A new crevasse needs at least one day to open, so even ice that is already critical calves at most once per model day (an illustrative choice).
  • Calved block: vertical heave ρi H z̈ = (ρi H − ρw d) g − damping settles to the Archimedes draught d = (ρi/ρw) H. Capsizing follows the metacentric height of a floating rectangle, GM = a²/(12 d) − (H − d)/2, negative (the block rolls over) when a/H < √(6 ρi/ρw (1 − ρi/ρw)) ≈ 0.75 (Weeks and Mellor).

Checks run in the page

  • First calving day from the closed form against a fine-step (0.05 d) run of the time-stepped model.
  • Dry-depth ratio for doubled strain rate against 21/3.
  • Floating block: numerical heave ODE against the Archimedes draught.
  • Berg stability: a separate polygon-clipping calculation of the righting lever (no GM formula) against the metacentric result.

Honest simplifications

  • One crevasse, constant ice properties, no tides, undercutting or ocean melt at the waterline, no basal sliding or surge. Real calving also depends on fjord geometry and ocean forcing.
  • The crevasse width is exaggerated for visibility; the 3D geometry is a diagram of the 1-D model. Bergs are drawn as a rectangular block; after capsizing the animation is approximate (the stability test itself is not).
  • Berg motion is animated in real seconds, the glacier clock in model days.

What to try

  • "Dry, cold winter" never calves; "Warm ice, heavy melt" calves within weeks.
  • "Tall thin berg" calves a block with a/H well below 0.75 and it rolls over; raise the block length Lc to 500 m and it stays upright.
  • "Floating tongue": Hab < 0 and the freeboard drops to about 10 % of the thickness.
Loading model...
Loading Blender model...
Crevasse depth vs freeboard
Water in the crevasse
Front position (calving sawtooth)
Made with 🟠 Blender · Three.js