Presets
Playback
Parameters
Camera
Layers
Quality
Model check
The science
What is modelled
Euler's disk is a heavy disk that is spun on its edge on a smooth surface. It wobbles down with a rising whirr, and the whirr speeds up just before it stops. The page integrates the full rigid-body equations of a thin disk that rolls without slipping on a flat horizontal table, in three dimensions. Nothing is scripted: the tilt, the precession and the final rush all come out of the equations of motion.
Equations
- Thin disk of mass m and radius a: moment of inertia about its axis
C = m a²/2, about a diameterA = m a²/4. The table touches the lowest rim point, atrc = a (−up + (up·n) n) / |−up + (up·n) n|from the centre (n is the symmetry axis). - Newton and Euler:
m dv/dt = F + m g,I dω/dt + ω × Iω = rc × F + τR. The contact force F is found at every step by demanding that the contact point does not move,v + ω × rc = 0for all time (its acceleration is set to zero, with a small stabilising term), which is a 3 by 3 linear system. Position, orientation (a quaternion) and angular velocity are advanced with fourth-order Runge-Kutta (step 0.2 ms). - Exact steady state (alpha is the tilt of the disk from the table): the centre of mass stands still at height
a sin α, the contact point circles at the precession rateΩ² = 4 g / (a sin α), and the angular velocityω = Ω sin αlies in the plane of the disk. Its energy isE = 3 m g a sin(α) / 2. For small tiltsΩ ≈ √(4g/(aα)), which diverges as the disk goes flat. - Rolling resistance: the surface and the rim deform a little, so there is a torque opposing the rotation,
τR = −κ ω/|ω|withκ = μr m g(the arm μr is the slider, tens of micrometres). It removes energy atdE/dt = −κ |ω| = −κ Ω sin α. Combined with the steady-state energy this gives the one-variable equationdα/dt = −κ Ω sin α / (1.5 m g a cos α), which behaves like−√αand therefore reaches zero tilt in a finite time.
Checks run in the page
- Measured precession rate of the launched steady state against
√(4g/(a sin α)). - Energy conservation without resistance and the closed-form steady-state energy.
- No slipping, no sideways wandering of the centre of mass, constant tilt.
- Decay run against the independent one-variable quasi-steady equation (tilt at several times and the settling time).
- Energy budget: energy lost equals the integral of κ|ω| dt.
- Small-angle limit, scaling of the precession with the tilt, and the size of the Blender model.
Honest simplifications
- Real Euler's disks last a minute or more and are limited mainly by rolling resistance and by the air squeezed in the thin wedge between disk and table (Moffatt, 2000, described the finite-time singularity). This page uses only a Coulomb-like rolling-resistance torque. The settling time and the exact shape of the final rush therefore depend on that model; the arm μr = 0.07 mm is a representative value for steel on glass, not a measurement.
- The disk is treated as infinitely thin for the inertia (a real one with thickness 10 mm and radius 38 mm has a diameter inertia about 2 % larger), and the table is rigid and flat. A real concave base would add a slight restoring force.
- No air drag, no sliding at the contact (the real disk slips a little at the end), no bouncing when the disk lands. The last 0.5 degrees are shown as the disk dropping flat; the true last stage would be a rapid vibration of the rim on the surface.
- The sound option only maps the pitch to the precession rate for illustration; a real disk's sound spectrum is richer.
- The mass does not matter: the weight, the inertia and the resistance torque all scale with it, so the motion depends only on the radius, the tilt and the resistance arm.
What to try
- Set the time scale to 0.15 and watch the contact point (orange trail) circle ever faster while the axis (blue line) falls.
- Pick "Large disk (6 cm)": the whirr is lower because Ω grows as
a-1/2. - Compare "Very smooth table" and "Sticky table": the shape of the tilt curve is the same, only the time axis stretches.
Loading model...
Loading Blender model...