3D Shock Absorber

A coil-over damper on a car wheel: drive over bumps, kerbs and potholes and tune the spring and damper.

Switch to 2D

Presets

Playback

Suspension

Road and speed

Camera

Layers

Quality

Model check

The science

What is modelled

One corner of a car: a quarter of the body (the sprung mass) rides on a coil spring and a hydraulic damper above a wheel (the unsprung mass), and the tyre itself is a second spring. The road moves under the wheel with a bump, a kerb, a pothole, a washboard or a random profile. The damper turns the motion energy into heat by pushing oil through small valves in the piston.

Equations

  • Body: ms z̈b = −ks(zb−zw) − c(żb−żw)
  • Wheel: mu z̈w = ks(zb−zw) + c(żb−żw) + kt(r−zw), where r is the road height. Heights are measured from the static equilibrium, so gravity does not appear except in the limit that the tyre cannot pull on the road: the tyre force cannot fall below −(ms+mu)g.
  • Damping ratio of the body: ζ = c / (2 √(ks ms)); ζ < 1 oscillates, ζ = 1 is critical, ζ > 1 is slow and stiff. Comfortable road cars use about 0.2 to 0.4.
  • Undamped modes: mu ms λ² − (ks(ms+mu) + kt ms) λ + ks kt = 0 with λ = ω²: a slow body mode near 1 to 1.5 Hz and a fast wheel-hop mode near 10 to 15 Hz.
  • Frequency response to a sine road r = R sin ωt from the complex impedances Y = ks + iωc, D1 = −ω²ms + Y, D2 = −ω²mu + Y + kt: Zw/R = kt / (D2 − Y²/D1) and Zb = Y Zw / D1.
  • Power turned into heat: P = c vrel². The compression side can be made softer than the rebound side with the share slider, as on real dampers.
  • The equations are integrated with fourth-order Runge-Kutta at 1 ms. Rubber bump stops add a stiff spring beyond 90 mm of travel.

Checks run in the page

  • Energy balance: with no damper the total energy is conserved; with a damper the energy lost equals the integral of c vrel² dt.
  • The simulated undamped body and wheel-hop frequencies match the closed-form eigenvalues.
  • The simulated steady-state amplitude to a 2 Hz sine road matches the complex transfer function.

Honest simplifications

  • This is the classic two-mass quarter-car model: vertical motion only, no pitch, roll or anti-roll bar, a linear tyre without damping and a single contact point (a real tyre envelops small bumps and filters sharp edges). Real dampers are nonlinear in speed and have temperature-dependent oil; here the force is linear on each side of zero speed. The picture can be vertically exaggerated for clarity (the slider), the numbers are not exaggerated.

What to try

  • Hit the speed hump with the worn damper preset (low c) and count the bounces, then raise c until the body settles in one motion.
  • Choose the washboard at body resonance and see the body amplitude exceed the road amplitude; then the wheel-hop preset, where the wheel is excited and the tyre may lose contact.
  • Watch the force-speed loop: a larger rebound share makes it lopsided.
  • Raise c to the maximum and notice that the body follows the wheel over short bumps: stiff, not comfortable.
Loading model...
Loading Blender model...
Road, wheel and body height over time
Damper force against relative speed
Frequency response: body and wheel
Made with 🟠 Blender · Three.js