Hot Air Balloon: Buoyancy, Burner Heat Balance, Vent and Wind Layers

A 2800 m3 balloon on a Blender-built model: the air must be about 100 C to float; fly it with burner and vent, and let the wind layers carry you.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A sport hot-air balloon with an envelope of 2800 m³ (about 18 m wide), a basket with two burners and propane tanks, a parachute vent at the crown and a pilot who flies it. The envelope is open at the bottom, so the air inside is at the same pressure as the air outside; heating it makes it expand and spill out of the mouth, which lowers its density. The balloon floats when the weight of the displaced cold air exceeds the total weight (fabric, basket, fuel, people and the remaining hot air).

Equations

  • Gas law: ρ = p/(R T), so hot air at 100 °C weighs 0.95 kg/m³ against 1.225 kg/m³ for 15 °C air. The mass of hot air inside is mi = p V/(R Ti).
  • Net force: F = (ρa − ρi) V g − M g. The floating temperature is Tn = Ta / (1 − M/(ρaV)).
  • Vertical motion with drag and added mass: (M + mi + ½ρaV) dv/dt = F − ½ ρa Cd A v|v|, so a steady climb rate is √(2F/(ρa Cd A)).
  • Heat balance of the hot air at constant pressure: mi cp dTi/dt = η Q − h As (Ti − Ta) − (qv/V) mi cp (Ti − Ta), with burner power Q (fuel energy 46 MJ/kg, η = 0.9), fabric loss coefficient h over As = 1000 m², and the vent flow qv = Cv Av √(2 g H (ρa − ρi)/ρi) replaced by outside air at the mouth.
  • Atmosphere (ISA): T = T0 − 0.0065 z, p = p0(T/T0)5.2559. Wind: speed w10(z/10)0.22 with a direction that turns (veers) with height; the balloon drags toward the local wind, so it can steer only by changing height.

Checks run in the page

  • Air density against the published 1976 US Standard Atmosphere at five heights.
  • Steady climb rate against √(2F/(ρ Cd A)).
  • Heating without losses against the closed form T1 exp(η Q t R/(p V cp)).
  • Ten-minute cooling against the closed form of dT/dt = −k T (T − Ta).
  • A steady hover: with exactly the burner power h A (Tn − Ta)/η the temperature and height stay put.

Honest simplifications

  • The hot air is one lump with a single temperature; real envelopes are warmest at the crown, which gives extra lift for the same mean temperature, and there is a pressure difference inside that is ignored.
  • Fabric loss is a single effective coefficient (conduction, convection and radiation together); real values depend on the wind, the fabric and the sun. The same goes for Cd = 0.45 and the added-mass factor.
  • The burner is a heat source with fixed efficiency; the vent mixes outside air instantly. Envelope shape is fixed except for a purely visual sag when the air is cold. Balloon, basket and fabric masses are typical round numbers, not a particular aircraft.
  • Wind is a smooth made-up profile that depends only on height, with no turbulence, thermals or terrain. The flight happens over a flat, endless, repeating field.
  • This is an educational model: real flights need training, weather briefings and air-traffic rules.

What to try

  • Hold the burner and watch the air temperature climb past the "needed to float" line; the balloon lifts off a little after it crosses.
  • Press Autopilot at 600 m: the burner pulses and the vent trims the climb rate.
  • Raise the load to 450 kg or lower the ground temperature and see how much hotter the air must be.
  • Fly at different heights to find the wind layers; veering lets you steer by going up or down.
Loading model...
Loading Blender model...
Altitude against flight time with the autopilot target
Air temperature inside, temperature needed to float, and outside air
Ground track with the wind at the balloon height
Made with 🟠 Blender · Three.js