Presets
Playback
The blob
Volume is injected or withdrawn by the syringe pump.
The liquid and gravity
Galinstan: 500 mN/m, 6440 kg/m3.
Electrowetting
Lippmann-Young voltage across an insulating layer under the blob.
Actions
Camera
Quality
Layers
Model checks
The science
Why a liquid metal blob stays round, and when it goes flat
Liquid metals such as galinstan and mercury have a large surface tension sigma (roughly 0.5 N/m, seven times that of water) and a large density rho. Two forces compete: surface tension pulls the surface into the shape with least area, a sphere, while gravity pulls the liquid down and spreads it. The balance sets the capillary length lc = sqrt(sigma / (rho g)) (about 2.8 mm for galinstan on Earth). A blob much smaller than lc is a spherical cap; a blob much larger is a flat puddle whose thickness no longer grows with the volume. The Bond number Bo = rho g R^2 / sigma (with R the radius of a sphere of the same volume) is the same comparison in one number.
The shape: Young-Laplace equation
The pressure jump across the surface is sigma (k1 + k2), the sum of the two principal curvatures. Inside the liquid the pressure grows with depth z below the apex, so k1 + k2 = 2/b + z / lc^2, where b is the radius of curvature at the apex. For an axisymmetric blob, with phi the slope angle of the surface and s the arc length, this becomes the set dx/ds = cos phi, dz/ds = sin phi, d phi/ds = 2/b + z/lc^2 - sin phi / x. The page integrates it with a fourth-order Runge-Kutta scheme from the apex until the slope reaches the contact angle theta, and adjusts b by bisection until the enclosed volume V = pi integral x^2 sin phi ds equals the injected volume. Graph 3 shows both curvatures along the profile: their sum rises linearly with depth, which is the hydrostatic pressure.
Contact angle and electrowetting
Young's equation fixes the angle where the liquid meets the surface; galinstan is non-wetting on glass (around 150 degrees, helped by its oxide skin). Putting an electrode and a thin insulating layer under the blob adds electrostatic energy, and the Lippmann-Young equation gives cos theta = cos theta0 + eps V^2 / (2 sigma d), with eps the permittivity of the insulator (3 eps0 here), d its thickness and V the voltage. A higher voltage or a thinner layer flattens the blob. Real devices stop at a saturation angle; the page clamps at 50 degrees. The contact line responds with a first-order delay of a chosen time constant.
The three checks
(1) A tiny blob (volume 3e-6 lc^3) must reproduce the spherical cap formulas exactly, because gravity is negligible. (2) A large puddle (1000 lc^3) must approach the infinite-puddle thickness 2 lc sin(theta/2) from above, with a finite-size excess that shrinks like lc/R. (3) The vertical force balance on the whole blob, 2 pi r sigma sin(theta) = pi r^2 (2 sigma/b + rho g H) - rho g V, tests the integration and the volume quadrature on the current settings.
Simplifications
The blob is axisymmetric and in equilibrium for the current angle; contact angle hysteresis, the oxide skin that makes real galinstan stick, evaporation, drop oscillation and viscosity are not modelled. The syringe is only drawn. The electrowetting angle is the ideal Lippmann-Young value with a hard saturation. The model is educational physics, not a device design.
What to try
- Start with the default galinstan blob and the dashed spherical cap: at 80 uL they already differ because the Bond number is not small. Press "Switch gravity off" and the blob becomes the cap.
- Drag the volume to 1000 uL. The height stops growing near 2 lc sin(theta/2); only the diameter increases (graph 1, green line).
- Pick "Electrowetting: 150 V flattens it" and watch the angle relax on graph 4. Make the insulator 0.3 um thick for a much stronger effect, or push the voltage to the saturation angle.
- Compare "Mercury bead" with "Water on a super-repellent surface": the capillary length and the shape change with sigma / rho.
- Open the pressure layer: the apex is at 2 sigma / b, the base is higher by rho g H.