Magnet and Paperclips (2D side view)

Press anywhere to place the magnet over the clips: see the field lines, the compass arrows and the pull on each steel clip.

Switch to 3D

Presets

Play

Playback

The magnet

Press or drag anywhere in the picture to move the magnet. Keys: arrows move it, Q/E tilt it.

The clips and the world

Layers

Model checks

The science

What a magnet does to a paperclip

A steel paperclip is not a magnet until you bring one near. Its iron atoms act like tiny compass needles, and an outside field B lines them up, so the clip gains an induced magnetic moment pointing along the field. A bigger field lines up more of them, up to a limit: m = mmax tanh(B / Bc). The purple curve on the third graph is this law and each white dot is one clip.

Why the clip is pulled, not only turned

A moment m parallel to the field feels the force F = (m·∇)B. Because the field outside a magnet has no curl, this reduces to F = m(|B|) ∇|B|: the clip is always pushed toward the place where the field is stronger, whichever pole is nearby. That is why both ends of the bar attract and why a magnet never pushes a clip away.

The bar magnet in the model

The bar is two magnetic poles ±q a distance d apart (softened by 7 mm so the field stays finite at the surface), with q = mbar/d and mbar = Br V / μ0. Each pole gives B = (μ0/4π) q r / (r² + ε²)3/2. Far away the pair is a dipole, B = 2(μ0/4π) m / r³, so the field falls off very fast with distance and the force falls off faster still (roughly r-7 before the steel saturates). The first graph shows where the pull equals the weight m g: above that height a clip stays on the table.

Aluminium, and clips holding clips

Aluminium is only very weakly paramagnetic (susceptibility about 10-5), so the teal clips respond with a moment millions of times smaller than steel: the model sets it to zero. A magnetised steel clip is a small dipole and magnetises its neighbours, which is why clips hang from each other in chains; untick "Clips magnetise each other" to see them hang only from the magnet.

Three checks run inside this page

(1) The force the engine computes by finite differences on the magnet axis is compared with the exact derivative of the pole-pair field. (2) The far field is compared with the dipole law and its log-log slope with -3. (3) The lift-off height found by really time-stepping a clip is compared with the root of F(h) = m g solved separately.

Honest simplifications: the bar is a pole pair, not a measured field map; each clip is a point with a fixed moment curve and its long axis is assumed to align with the field at once (no torque dynamics, no magnetic memory or hysteresis); collisions use spheres 1.9 cm wide, so the hooking of wires is only imitated by damping; the magnet is moved by your hand and feels no reaction force. The default numbers (Br = 0.15 T, clip 0.8 g) give a lift-off range of a few centimetres, similar to a small fridge magnet.

What to try
  • Switch Demo sweep off, press in the picture to place the magnet and slowly lower it over a clip: the clip jumps up as soon as the pull passes its weight.
  • Choose Pole down: lift a chain: clips hang from each other. Untick "Clips magnetise each other" and the chain disappears.
  • Choose Steel + aluminium mix: the teal clips are ignored by the magnet.
  • Press Switch the magnet off: the induced magnetism vanishes and everything drops (steel keeps no memory in this model).
  • Choose Floating in space and shake: with no gravity even a weak pull gathers the clips.
  • Look at the little compasses: red tips point the way the field points, from N to S outside the magnet.
Pull on a steel clip against its height (below the magnet)
Field of the bar on its axis (log-log): a straight line of slope -3
How strongly the clip steel magnetises (m / m_max against B)
Clips held and lifted over the last 30 s
Made with 🟠 Blender