loading...
running...
How to use
- Pick a preset, then change one slider at a time. The orange curve in the first graph is the net shaft power at every speed; the green dot is where the wheel runs now.
- Press Set load for maximum power, then compare with Light load and Heavy load: the best speed is not the fastest and not the slowest.
- Raise the flow Q on the overshot wheel until the buckets are full: extra water is wasted (see "Water not captured").
- Raise the tailwater depth: the lowest buckets are drowned, head and torque fall.
- On the undershot wheel try flat and curved floats and find the 50 % limit in the efficiency graph.
- Reset restarts the wheel from rest; Drag to orbit, wheel to zoom, the buttons jump to preset cameras. Space pauses.
The mill house, dam with culvert, pond basin, trees, rocks, flume and the timber wheel parts (buckets, arms, axle) were modelled in Blender with baked PBR textures and exported as a Draco GLB; the wheel is assembled from them by Three.js for the chosen radius, width and bucket count.
The science
A water wheel converts the hydraulic power P_hyd = ρ g Q H of a stream (flow Q in m³/s, head H in m) into shaft power. What it manages to keep is the efficiency η = τ_load · ω / P_hyd.
Bucket wheels (overshot and breastshot)
Each of the N buckets is followed from the inlet angle φ_in (measured from the top, in the direction of rotation) to the angle φ_E where its mouth reaches the tail water. Water arriving at flow Q shares itself among the buckets that pass the inlet per second, so a bucket takes up
V_in = min( 0.85 V_b , 2π Q / (N ω) )
A bucket keeps its water until the spill angle φ_s (earlier when it is fuller and when the wheel is fast, because the centrifugal ratio Fr = ω² r / g pushes water out of the open mouth), then empties linearly until φ_E. The weight torque is the sum over all buckets
τ_w = (1 - leak) ρ g r_cg Σi V(φ_i) sin φ_i
and the entering jet adds the impulse term τ_j = ρ Q_cap ( v cosβ - ω r_cg ) r_cg, which turns negative when the rim runs faster than the water, because the water must be accelerated to rim speed. The head is H = R (1 + cosφ_in) + v²/2g - tail depth.
Undershot (stream) wheel
The floats change the momentum of the stream: F = k ρ Q ( v - u ), P = k ρ Q ( v - u ) u with rim speed u = ω r. The maximum is at u = v/2 and gives η_max = k / 2 of the kinetic power ½ ρ Q v²: exactly 50 % for flat boards (k = 1). Curved Poncelet floats turn the water back; k = 1.3 is used here, which includes entry and exit losses and gives about 65 %, in line with historic measurements. If the stream is deeper than the float depth the extra water passes over the floats and is lost.
Dynamics
I dω/dt = τ_drive - τ_load - τ_friction , I = 0.8 m R² , m = 40 + 160 R W kg
The page integrates this with a fixed 1/240 s step. A constant load (millstone) or a generator load τ = C ω can be selected. The "predicted steady speed" in the readout is found by a separate root finder on the phase-averaged torque, so it is an independent check of the time-domain run.
Honest simplifications
- Quasi-steady filling, not free-surface fluid dynamics: the spill angles, the leak fractions (4 % overshot, 12 % breastshot) and the centrifugal factor are assumed values chosen to give historic efficiencies (overshot 60-85 %, breastshot 50-70 %), not measured ones.
- The wheel mass and moment of inertia are estimated from the size, there is no gear train, and the water in the buckets is not added to the inertia.
- The numbers are illustrative; this is a teaching model, not a design tool for building a real wheel.