Presets
Playback
Wind
Petal
Fall and display
Camera
Layers
Quality
Model check
The science
What is modelled
Every falling petal is a thin elliptical plate (length L, width 0.8 L, mass per area σ) that moves as a full three-dimensional rigid body: three position coordinates, a quaternion for orientation and an angular velocity, advanced 300 times per second. The wind blows through a grove of six cherry trees; petals are shed from the blossom clumps, faster in stronger wind, and land on the lawn or on the pond, where they drift with the surface current.
Equations
- Wind:
U(z) = U10 (z/10 m)α(power-law boundary layer) times1 + Ig g(t - x/c), where g is an Ornstein–Uhlenbeck process (unit variance, correlation time τ) that travels downwind at about 0.8 U10, plus three travelling turbulence modes that also give a small vertical component. - Relative velocity
vr = v - u(x,t), Reynolds numberRe = ρ |vr| L / μ, angle of attacksinα = |vr · n| / |vr|(n is the plate normal). - Force:
F = ½ ρ A |vr|² (CL l - CD v̂r)withCD = CD0(Re) + (CD90(Re) - CD0) sin²α,CD90 = 1.17 + 64/(π Re)(the second term is the Stokes disc limit),CD0 = 0.03 + 2.66/√Re(laminar skin friction on both faces) andCL = 0.4 · 2 sinα cosα(thin-plate lift with a finite-aspect-ratio reduction). - Torque: the pressure centre sits a quarter chord behind the leading edge at small α and moves to mid-chord broadside,
rcp = 0.25 L (1 - sinα); a cupped petal also has its centre of mass below the pressure centre byh = c L(parachute stability); rotation is damped by-(k |ω| + 32 μ a³/3) ωon each body axis, and Euler's equations with the plate's principal inertias (plus the added inertia of the fluid it drags,π ρ a⁴ W / 8) give the angular acceleration. - Motion:
m dv/dt = m g + Fwith the added mass of the entrained air (½ π ρ a b²) included along the normal. - Broadside terminal speed:
vt = √(2 m g / (ρ A CD90(Re))), solved as a fixed point because Re depends on vt. The regime of a real fall (steady, fluttering, tumbling) is not prescribed: it follows from the dimensionless inertiaI* = σ/(ρ L), the Reynolds number, the cupping and the turbulence. The tracked-petal panel classifies it from the range of the tilt angle over the last two seconds.
Checks run in the page
- A petal pinned broadside for 10 s against the drag-balance terminal speed.
- A 0.05 mm disc in the viscous limit against Stokes' disc law
m g / (8 μ d). - A petal in a steady 4 m/s wind against the requirement that its horizontal speed reaches the wind speed.
Honest simplifications
The aerodynamic model is quasi-steady: it uses force and moment coefficients for a flat plate and does not resolve vortex shedding, so the flutter and tumble frequencies are plausible but not measured. The default petal (12 mm, 25 g/m² ≈ 2.4 mg) is representative, not a measurement of a particular cultivar. Petals are drawn up to eight times larger than real size so they can be seen from a few metres away (the display multiplier). The wind field is a model, not a CFD solution: the trees do not shelter the air, and the canopy does not change the turbulence. Petals landing on the pond drift with a surface current of 3 % of the wind speed and stop at the shore; waves and sinking are not modelled. The tree and blossom shapes are artistic; only the physics of the petals is quantitative.
What to try
- Release a tracked petal in calm air and watch it flutter side to side, then repeat with the "Flat petals (tumbling)" preset (large, heavy, no cupping) and see the tilt angle go past 120 degrees.
- Raise the areal density: the fall speed rises as the square root, and the Reynolds number follows.
- Use "Petal storm": gusts shed far more petals and carry them across the pond.
- Rotate the wind by 90 degrees and watch the landing-distance histogram shift.
- Shrink the petal to 6 mm and 10 g/m² and note how the Reynolds number and the drag coefficient move along the curve in the last graph.
Trees, pond, bridge and petals were modelled in Blender and baked to PBR textures; Three.js animates every petal from the physics module above.