Wind Tunnel Boundary Layer Lab (2D)

Flow along a flat plate: laminar Blasius layer, transition, turbulent layer, pressure gradient and roughness.

Presets

Playback

Flow

Surface and turbulence

Probe and animation

Layers

Model check

The science

What a boundary layer is

Fluid touching a surface sticks to it (no-slip), so the speed rises from 0 at the wall to the free-stream value U over a thin layer of thickness delta. Inside that layer viscosity matters; outside it the flow behaves almost like an ideal fluid. Skin-friction drag comes from the wall shear tau_w = mu du/dy at the wall, usually written as the coefficient Cf = tau_w / (0.5 rho U^2).

Laminar layer: Blasius and Falkner-Skan

For a flat plate with no pressure gradient the layer follows the Blasius similarity solution of f''' + f f'' + beta (1 - f'^2) = 0 with beta = 0. The simulator solves this ODE by RK4 shooting on f''(0) until f'(infinity) = 1, which gives delta99 = 4.91 x / sqrt(Re_x), delta* = 1.721 x / sqrt(Re_x), theta = 0.664 x / sqrt(Re_x), Cf = 0.664 / sqrt(Re_x) and shape factor H = delta*/theta = 2.59. A free-stream speed Ue ~ x^m (pressure gradient, beta = 2m/(m+1)) changes the profile: favourable gradients (m > 0) make it fuller, adverse gradients make it thinner at the wall until the wall shear vanishes at beta = -0.1988, where the flow separates.

Transition and the turbulent layer

A laminar layer becomes unstable and turns turbulent at a transition Reynolds number around Re_x ~ 5e5, earlier with free-stream turbulence (here the empirical rule Re_tr = 5e5 (0.3/Tu%)^0.7 between 1e5 and 3e6) and at 1e5 with a trip wire. After transition the simulator integrates the momentum-integral equation d theta/dx = Cf/2 with the Ludwieg-Tillmann friction law Cf = 0.0328 Re_theta^-0.268 and a 1/7-power outer profile (delta = 72 theta / 7, H = 1.29). Turbulent mixing gives a much fuller profile, a thicker layer and about three times the wall shear. Near the wall the profile follows Spalding's law of the wall, u+ = y+ in the viscous sublayer and u+ = ln(y+)/0.41 + 5.0 in the log layer, with u+ = u/u_tau, u_tau = U sqrt(Cf/2).

Roughness

If the sand-grain height in wall units ks+ = ks u_tau / nu exceeds about 5 the wall stops being hydraulically smooth; above about 70 the friction follows the fully rough law Cf = (1.89 + 1.62 log10(x/ks))^-2.5. The model blends smoothly between the two.

What is simplified

The layer is two-dimensional and steady in the mean. Transition is a correlation, not a stability calculation, and the pressure gradient only enters the laminar part (the turbulent integration assumes zero gradient). The turbulent tracer motion is a random-walk cartoon of eddies, not a turbulence simulation. Display height is magnified, because real boundary layers are only millimetres thick. Educational model, not for design.

What to try

  • Compare the natural-transition preset with the tripped one: the layer thickens suddenly and Cf jumps up.
  • Raise free-stream turbulence and watch the transition point move toward the leading edge.
  • Choose the adverse-gradient preset and watch Cf go to zero near the end of the plate.
  • Switch to water: the same speed gives a Reynolds number 15 times larger.
Velocity profile at the probe
Layer thicknesses along the plate
Skin friction vs laws
Law of the wall (wall units)