Pitot Probe Nose Section (2D)

An axial cutaway of the probe: nose pressure map, static source error, line pressures and the two instruments.

Switch to 3D

Presets

Playback

Flight

Pressure altitude, true airspeed, climb rate, temperature and an airspeed oscillation.

Probe

Angle to the flow, how much angle it tolerates, and where the static ports are.

Pneumatic lines and instrument

Line length and diameter, instrument volume, drain hole.

Faults and experiments

Ice the probe or block the static port during flight.

Layers

Model checks

The science

What a pitot-static probe measures

This 2D view cuts the probe along its axis, which is where the half-body nose model is exact: the streamlines are drawn from the same stream function that gives the pressure coefficient.

The open ram port at the nose of the probe faces the flow. The air in front of it is brought to rest, so the port senses the total pressure Pt. Side holes (static ports) further back sense the pressure of the undisturbed air, Ps. The airspeed indicator is a differential pressure gauge that measures impact pressure qc = Pt - Ps; the altimeter measures Ps alone and converts it with the International Standard Atmosphere (ISA).

Why a simple 1/2 rho V^2 is not enough

For low speed qc = 1/2 rho V^2. Air is compressible, so the stagnation process is isentropic and qc = Ps [ (1 + 0.2 M^2)^3.5 - 1 ] with Mach number M = V / a, a = sqrt(gamma R T), gamma = 1.4. A series gives qc / (1/2 rho V^2) = 1 + M^2/4 + M^4/40 + M^6/1600 + ...: 1.5 % at M 0.25 and about 16 % at M 0.8. The instrument shows the calibrated airspeed CAS = a0 sqrt( 5 [ (qc / P0 + 1)^(2/7) - 1 ] ) (sea-level constants a0 = 340.29 m/s, P0 = 101325 Pa); it equals the true airspeed only at sea level in ISA conditions. In thin air CAS is lower than the true airspeed, roughly TAS ~ CAS / sqrt(rho / rho0) at low Mach.

ISA atmosphere

Below 11 km T = 288.15 - 0.0065 h and P = P0 (T / T0)^(g / (R L)) with g / (R L) = 5.2559; above it the air is isothermal at 216.65 K and the pressure falls exponentially. The slider "temperature offset" shifts T (density and sound speed) at the same pressure altitude.

Static source error: the nose of the probe

The probe nose is modelled as an axisymmetric Rankine half-body (a point source in a uniform stream). Its surface is R = a sqrt(2 / (1 - cos theta)) and the speed on it follows from the source and stream, which gives the surface pressure coefficient Cp = 1 - |V|^2 / U^2. Cp = 1 at the nose tip (the stagnation point where the ram port sits), then Cp dips to about -0.33 over the shoulder and tends to zero further back. A static port at distance x behind the nose therefore reads Ps + Cp q, which is why real probes put the ports six to eight diameters back: at 7 diameters the error is -0.3 % of q, at 1.2 diameters about -10 %.

Probe angle

A probe that is not aligned with the flow (sideslip or angle of attack) recovers less total pressure. The model multiplies qc by 1 up to the "angle tolerance" and then by cos^2 of a smooth ramp reaching zero at 90 degrees. This law is an illustrative, empirical stand-in: real tolerances (about 15 degrees for a plain tube, 30 degrees or more for a Kiel-type or heated probe) depend on the tip shape.

Pneumatic lines and lag

The tube from probe to instrument is a flow resistance R = 8 mu L / (pi r^4) (laminar Poiseuille; mu from Sutherland's law) feeding the instrument volume, a capacitance C = V / P (isothermal). The pressure in the line follows the probe pressure as a first-order lag with time constant tau = R C; the response to a sinusoid is 1 / sqrt(1 + (omega tau)^2) with phase -atan(omega tau). Thin, long lines at low pressure (high altitude) give long lags. The static line is modelled with 40 % of the instrument volume.

Icing and blockage

If ice closes the ram port but the drain hole stays open, the trapped air leaks out through the drain: dx/dt = -kappa sqrt(x (Pa + x)) with x = P_line - Pa, which has the exact solution 2 [ asinh sqrt(x0/Pa) - asinh sqrt(x/Pa) ] = kappa t. The airspeed indicator decays to zero although the aircraft has not slowed down. If the drain is iced too, the pressure is trapped and the airspeed indicator becomes an altimeter: qc_shown = Pt_trapped - Ps(h) rises in a climb and falls in a descent. A blocked static port freezes the altimeter and makes the airspeed read high in a descent and low in a climb.

Simplifications

Steady potential flow around the nose (no boundary layer, no tip hole, no internal flow); static pressure error is evaluated at the free-stream Mach number with the incompressible Cp; the Mach number is limited to 0.95 (no shock in front of the probe); the line is lumped (no wave delay, no distributed R-C line); orifice discharge coefficient 0.6; temperature of the trapped air is constant; the instrument case is ideal. The tolerance law above is empirical. Hose colours and the bench are illustrations.

What to try
  1. Start with Light aircraft cruising and then Airliner at Mach 0.78: compare true and indicated airspeed in the readouts and the first graph. At 11 km the indicated value is far below the true airspeed.
  2. Open Fast and low and watch the second graph: the dot shows how much the simple 1/2 rho V^2 would over-read at this Mach number.
  3. Press Ice over the ram port during cruise: the needle falls to zero in a few seconds although the true airspeed is unchanged. Time it against the drain-out readout.
  4. Press Ice ram port and drain, then set a vertical speed of +8 m/s and speed up time: the airspeed indicator rises while the aircraft flies at constant speed.
  5. Press Block the static port and set a descent: the altimeter freezes and the airspeed over-reads.
  6. Drag the static ports slider towards the nose (Cp graph) and read the static source error and the altitude error.
  7. Set an oscillation amplitude, make the line long and thin, and watch the indicated speed lag and shrink compared with the true speed.
Airspeed: true, ideal indicated and indicated here
Compressibility: impact pressure vs 1/2 rho V^2
Impact pressure: true and shown (last 40 s)
Pressure coefficient along the probe nose and static ports
Made with 🟠 Blender