Forest Campfire Safety Lab: Fuel Moisture, Wind, Slope and Ember Spotting

A campfire in a pine forest: choose how dry the fuel is, the wind, the slope and the cleared radius, then see whether embers escape and how a wildfire stretches along the wind.

Switch to 2D

Presets

Playback

Fuel bed

Tool (tap the ground)

Parameters

Camera

Layers

Quality

Model check

The science

What is simulated

A 64 m x 64 m forest floor of 1 m cells with grass, pine litter and brush, each with its own moisture. A campfire of adjustable heat release sits in a stone ring. Fire spreads from cell to cell, flying embers can start spot fires, and you can pour water, dig firebreaks or light fires anywhere.

Spread rate

The head spread rate is R = R0 eta_M (1 + c_w U^1.4): a still-air dry rate R0 for the fuel bed, a moisture damping eta_M = 1 - 2.59 r + 5.11 r^2 - 3.52 r^3 with r = M/Mx (the Rothermel polynomial, zero at the extinction moisture Mx), and a wind boost. The wind constants c_w and the R0 values are illustrative, not fitted to a particular fuel model.

Shape: the wind ellipse

Seen from the ignition point (one focus), the fire is an ellipse with length-to-breadth ratio L/B = 0.936 e^(0.2566 U) + 0.461 e^(-0.1548 U) - 0.397 (Anderson, U in mi/h). The spread rate in a direction psi from the wind is R(psi) = R_head (1 - e)/(1 - e cos psi) with e = sqrt(1 - (B/L)^2). Slope multiplies this by 2 for each 10 degrees uphill (a field rule of thumb, applied multiplicatively).

Spread across the map

Fire arrival is a minimum-travel-time (Dijkstra-type) problem on the lattice: each burning cell offers neighbours (16 around it) an arrival time distance / rate. A burning cell burns out after the fuel residence time. Moisture of soaked cells dries back with a one-hour time lag, dM/dt = (M_eq - M)/tau.

Intensity and flame length

Byram: I = H w R (H = 18 000 kJ/kg, w fuel load, R spread rate) and L_f = 0.0775 I^0.46. The campfire flame height follows Heskestad, L = 0.235 Q^(2/5) - 1.02 D. Fuel inside the radius d = sqrt(chi Q / (4 pi q_crit)) (radiant fraction 0.3, piloted ignition near 12.6 kW/m^2) catches without any ember.

Embers

Embers leave the flame at the plume speed w ~ 2 (g I / (rho c_p T))^(1/3) and fall at a terminal speed v_t of 0.8 to 3 m/s with linear drag, tau = v_t/g. The page uses the exact solution z(t) = z0 - v_t t + (w0 + v_t) tau (1 - e^(-t/tau)) and x(t) = U (t - tau (1 - e^(-t/tau))). An ember that burns out in the air is lost; one that lands on fuel with moisture M ignites it with probability 0.6 (1 - M/Mx). The probability and the emission rates are assumptions, not measurements.

Campfire safety (real life)

Check for fire bans first. Build the fire on bare mineral ground, clear flammable litter well beyond the stones, keep it small, keep water and a shovel next to it, never leave it alone, and put it out completely: drown it, stir, and feel that the ashes are cold. The page shows why: a small fire throws embers several metres downwind, and dry fuel catches them.

Simplifications

  • One cell holds one fuel type, with no vertical fuel layers, no crown fire and no change of wind inside the forest.
  • Spread constants, ember emission rates and ignition probabilities are illustrative, so use the page to see the trends (wetter fuel, clearing, wind) and not to predict a real fire.
  • Slope and wind are combined multiplicatively, not by Rothermel's vector addition.
  • No fire-induced wind, no spotting from burning trees, no suppression other than water and bare ground.

Checks

The six boxes under the controls run the page's own functions against independent calculations: the ellipse shape sampled numerically, the lattice spread against exact distances, the damping polynomial, an RK4 ember flight against its exact solution, radiation integrated over a sphere, and the drying law.

Loading model...
Loading Blender model...
Burnt area against time, with the ellipse theory
Head spread rate against fuel moisture
Where the campfire embers land
Made with 🟠 Blender · Three.js