loading...
Floor (red) and pool (orange) temperature over time; grey line is the steady floor temperature
Pool buoyancy margin (oil minus wax density) over time; the first blob needs a positive margin and Bo above 1
Start-up time versus bulb power (headless sweep of the same model); green dot is this run
running...
The science
The question. Everyone who has bought a lava lamp knows the first blob arrives long after you switch it on. The reason is a chain of three delays: the base warms to its steady temperature, the wax pool warms through the floor, and only then does the pool become lighter than the oil and strong enough (Bond number above 1) to release a blob.
1. Bulb to floor (energy balance).
C dTfloor/dt = P − h A (Tfloor − Troom) ⇒ Tfloor(t) = Troom + (P/hA) (1 − e−t hA/C)
with C = 69 J/K (a lumped thermal mass). A 25 W bulb with h A = 0.46 W/K gives a floor near 76°C after about 10 minutes (time constant 150 s). That is fast; the pool is the slow part.
2. Pool warming. The wax layer of depth h is heated through the floor and loses heat to the oil above it. With thermal conductivity kw and the heat capacity of wax, its warm-up time scales as ρ c h² / (2 k), tens of minutes for a 3 cm layer.
3. Release. The pool lifts off only when it is lighter than the oil above it, and the interfacial tension is overcome:
ρoil(T) = ρ0 [1 − βf (T − 20°C)], ρwax(T) = ρ0 (1 + δ) [1 − βw (T − 20°C)], ρ0 = 950 kg/m³
margin = ρoil(Toil) − ρwax(Tpool) > 0, Bo = margin · g r² / σ > 1
The graph shows the margin crossing zero. Cold start: the wax is a fraction of a percent heavier than the oil, so the margin is negative until the pool has warmed by roughly 20 K above the crossover.
The sweep graph. On load and whenever you change the recipe, the page runs the same model headlessly for bulbs from 12 to 45 W and plots the minutes to the first blob. Weak bulbs may not start at all within 4 hours (gap in the curve).
After release a blob follows the usual buoyancy plus drag motion:
(ρwax + ½ ρoil) V dv/dt = (ρoil − ρwax) V g − 6π μ r (1 + 0.15 Re0.687) (v − uoil), Re = ρ |v − u| 2r / μ
Stokes limit: vt = 2 g (ρoil − ρwax) r² / (9 μ)
Honest limits. Blobs stay spheres (never stretched), the oil is not solved (prescribed temperature field, fixed convection roll), material properties are constants of order of paraffin wax and mineral oil, and the blob-pool pinch-off time is a fitted constant. The start-up times are properties of this model with plausible material constants (a lamp's real start-up depends on its exact wax, oil and glass); they illustrate the three delays, they are not a prediction for a particular product. The pool is a single lumped layer; wax melting and latent heat are not modelled.
Numerical checks (run in this page). (1) Steady floor temperature at 40 W, hA 0.8, 10°C vs Troom + P/(h A); (2) warm-up time to 63.2 % at hA 0.30 vs C/(h A); (3) energy balance over 400 s: heat in − heat lost vs stored CΔT; plus the shared checks: Stokes terminal speed, thermal e-folding time, wax volume conservation, merge radius and momentum, Rayleigh number and the projected silhouette area of one blob in this renderer.
The backdrop, base, heater disc and cap are rendered from the same Blender scene as the 3D page (orthographic side view, Cycles on the GPU, exported as small WebP sprites); the wax is drawn live in Canvas from the blob positions. The physics runs on the spheres, not on the drawn picture.
The 2D view. This page runs exactly the same lamp model as the 3D page (same lamp.js, same controls, readouts, graphs and checks); only the drawing is flat. The wax is drawn as the iso-line of the same Wyvill-kernel field the 3D mesher uses (same iso level 0.4), projected along the viewing axis, so blobs that sit behind one another overlap and a blob that is merging in depth can look merged here before it is. The backdrop, base, heater disc and cap are Cycles renders of the Blender scene used by the 3D page. Light and shading on the wax are a simple 2D normal from the field gradient, not a ray-traced image.