Suspension Bridge Mode Lab 3D

vibration modes, vortex shedding and resonance of a stiffened suspension span

Switch to 2D

Presets

Playback

Load type

Bridge, wind and load

Playback and view

Camera

Layers

Quality

Model check

The science

Question. Why can a steady breeze make a long suspension bridge sway, and why does the same wind do nothing at another speed? Because the span is a set of vibration modes, each with its own natural frequency, and the wind sheds vortices at a frequency set by its speed. When the two match, the mode builds up: resonance.

Modes of a stiffened suspension span. The deck of length L and mass μ per metre hangs from a cable with horizontal tension H set by the cable sag f (parabolic cable under its own weight: H = μ g L2 / (8 f)) and has a bending stiffness EI. For small vertical motion y(x,t) with simply supported ends:

μ ytt = H yxx − EI yxxxx

Every shape sin(nπx/L) is a mode, with the natural frequency

fn = (1 / 2π) √( (H kn2 + EI kn4) / μ ), kn = nπ/L

For a floppy girder (EI small) the frequencies are equally spaced like a guitar string, fn = n f1. A stiff girder bends the spectrum upward (fn grows like n2). The deck is the sum y = Σ qn(t) sin(nπx/L); this page keeps the first six modes.

Each mode is a damped oscillator. With modal mass M = μ L / 2, stiffness K = M (2πfn)2 and damping ratio ζ:

M qn'' + 2 ζ √(K M) qn' + K qn = Pn sin(2π f t)

Pn is the load projected on the shape: Pn = ∫ p(x) sin(nπx/L) dx. A load that is uniform along the span (load 1) is symmetric, so it feeds only the odd modes 1, 3, 5 and exactly cancels the even ones; a gust on the left third (load 2) or a point load at L/4 (load 3) is not symmetric and excites all of them. The page integrates each mode exactly over every time step (the force is held constant within a step), so any damping and any time compression stays stable.

Vortex shedding. A bluff deck of depth D in a crosswind U sheds alternating vortices at the Strouhal frequency fs = St U / D (St about 0.2), which pushes the deck up and down with an oscillating lift of amplitude p = ½ ρ U2 D CL per metre. Resonance occurs at the wind speed Un = fn D / St. At resonance the response is limited only by damping: the amplitude is Pn / (2 ζ K), a factor 1/(2ζ) (62 for ζ = 0.8 %) above the static deflection.

Three independent checks run in the page. (1) The fundamental frequency from a finite-difference discretisation of the equation (91 nodes, inverse iteration) must match the closed form above. (2) The static mid-span sag under a uniform load, computed by solving EI y'''' − H y'' = w with finite differences, must match the sum over modes; the page also shows how much the six-mode truncation misses. (3) Mode 1 driven by vortex shedding at its own frequency must reach the closed-form resonance amplitude P / (2 ζ K) when it is simulated for eight decay times.

Honest simplifications. Linear, small-amplitude vibration of one span with pinned ends; the cable is a parabola with hangers that do not stretch, so the symmetric modes of a real suspension bridge, which also stretch the cable (an extra stiffening term), are somewhat stiffer than this model gives; the side spans, flexible towers, torsion and twisting of the deck, aeroelastic flutter (the mechanism behind the 1940 Tacoma Narrows failure) and wind turbulence are not modelled; the vortex lift is a pure sine at fs with no lock-in. The default numbers describe a generic long-span bridge, not a specific one. The deflection is drawn magnified (the real amplitude is shown in the readouts); the traffic and the ship are decoration only.

Press a preset and the deck is already built up to the resonance. Then try: (1) Same span, wind far off resonance against wind tuned to mode 1: the same wind, completely different swing. (2) Tune to mode 2: a uniform wind cannot excite an even mode, so the mid-span stays still. (3) Gust on the left third: now mode 2 moves. (4) Damping 4 %: the resonance is cut by a factor of five. (5) Press Tune load to selected mode after changing the span, sag, mass or girder stiffness. (6) Pluck shows free decay at the mode's own frequency.

Loading model...
Loading Blender model...
Steady-state mid-span amplitude against load frequency (log scale, numbered lines are the modes)
Deck displacement at mid-span and quarter span
Amplitude of each vibration mode
Vibration energy in all modes and in the selected mode
Made with 🟠 Blender · Three.js