READY TO START
CUTAWAY / MODEL R7
Engine R7 · Radial aircraft powerplant · Mechanically linked seven-cylinder cutaway

A radial engine, assembled and set in motion

Explore the architecture of an odd-cylinder, four-stroke radial aircraft engine. Seven finned cylinders surround a single crankshaft. One master connecting rod drives the upper piston, while six articulated rods transmit the crank motion to the remaining pistons. A front-facing section view exposes each moving part without removing the engine from its illustrated museum stand.

How the simulation works

The geometry uses crank-slider constraints rather than scripted piston oscillation. The master rod is solved exactly within its chosen two-dimensional linkage. Articulated rod pins follow the orientation of the master rod, and secondary piston positions are obtained by satisfying each link's length constraint along its cylinder axis. Engine rotation follows a fixed-step angular momentum balance, with throttle-dependent combustion torque, friction, starter torque, and an adjustable external load.

The combustion model is intentionally simplified and is designed to explain mechanical relationships, not reproduce measured engine performance, detailed thermodynamic cycles, manifold dynamics, or structural stress.

7Radial cylinders
4 strokes720° crank cycle
0.46 mIllustrative crank radius
14 kg·m²Modeled rotational inertia
120 HzFixed physics integration
1–3–5–7–2–4–6Firing sequence

Instructions

Press Start engine to engage the starter and initiate rotation. Adjust throttle and propeller load while watching RPM and shaft power. Disable ignition to observe the engine coast or stall. Pause to inspect connecting rods; turn the propeller on and off to reveal the crankshaft. Orbit, zoom, and click any labeled component to learn more.

Radial engine questions answered

1. Why do radial aircraft engines have an odd number of cylinders?

A single-row four-stroke radial engine commonly uses an odd cylinder count so evenly spaced ignition events can advance around the row in a workable sequence. With seven cylinders, firing events occur 720° ÷ 7 apart. The order used here is 1–3–5–7–2–4–6.

2. What is a master connecting rod?

The master rod joins one piston directly to the crankpin and carries smaller articulated pins for the remaining connecting rods. This arrangement allows one crank throw to coordinate a complete radial bank without giving every piston a separate crank throw.

3. What does the four-stroke cycle consist of?

Intake draws in charge, compression raises its pressure, combustion expands the gases to perform work, and exhaust evacuates the products. An individual cylinder completes the cycle in two full crankshaft revolutions, or 720°.

4. How is engine RPM calculated in this exhibit?

Rotational speed is integrated from the net applied torque divided by rotational inertia. The angular speed in radians per second is converted to revolutions per minute by multiplying by 60/(2π).

5. Why does additional propeller load reduce RPM?

The propeller load opposes crankshaft rotation. With throttle unchanged, more resisting torque reduces net accelerating torque and the engine slows toward a different operating point, or stalls if it cannot produce enough power.

6. Why are air-cooled cylinders covered in fins?

Cooling fins increase the exposed surface area available for convective heat transfer to surrounding airflow. The illustrated fin arrays also reveal the separation between the cylinder barrels and the heavily ribbed cylinder heads.

7. Are the visible piston and connecting-rod movements physically constrained?

Yes, within a simplified planar master-and-articulated-rod mechanism. Pistons move along fixed cylinder axes, secondary pin locations are attached to the computed master-rod orientation, and every rod maintains its assigned center-to-center length.

8. Does this exhibit calculate actual fuel consumption or exhaust temperature?

No. Neither quantity is displayed because the illustrative torque model does not include a calibrated fuel-flow or heat-transfer calculation. Visible exhaust particles indicate valve timing; they are not a computational fluid-dynamics result.

9. What is the difference between WebGPU and WebGL rendering?

WebGPU is a modern browser graphics API. This exhibit prefers the Three.js WebGPU renderer when supported, but uses its WebGL 2 fallback on compatible devices without WebGPU. The mechanical solver itself runs on the CPU in both cases.

10. Can this model be used for engineering design certification?

No. Although the linkage relationships and rotational dynamics are mathematically meaningful, geometry proportions, valve motion, combustion torque, friction, and visual exhaust are illustrative simplifications. Use a validated engineering solver and measured data for design decisions.

Made with 🤖 ChatGPT · Three.js