Decline Haulage: Truck Power Balance, Single-Lane Passing Bays and Fleet Throughput

Haul trucks climb an underground decline on a single lane: how fast a loaded truck can climb, where trucks must wait in passing bays, and how many trucks the loader, the lane and the hopper can feed.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A fleet of haul trucks climbs a decline (an inclined mine road) with ore from a loader at the bottom to a hopper at the top, and returns empty. The ramp is drawn straight; a real decline is usually a spiral, which changes the curve resistance and the speed on bends but not the climb physics.

Truck on a grade

With grade angle theta (tan theta = rise/run), mass m, rolling resistance Crr, air density rho and drag area CdA:

m (1+k) dv/dt = F_drive - m g sin(theta) - Crr m g cos(theta) - 1/2 rho CdA v^2, with F_drive = min(P / v, mu m g cos(theta)).

The steady climbing speed solves P = v F_resist(v). For the default 72 t loaded truck on 12.5 % this is about 2.9 m/s (10.6 km/h) with 340 kW at the wheels: nearly all the power lifts the load, and the speed falls as 1/grade. Downhill an empty truck is pulled by m g (sin theta - Crr cos theta); the retarder must turn that force times the speed into heat and can absorb 600 kW, so the descent speed is the smaller of the speed limit and P_ret / F_net. Starts are limited to 1 m/s2 (operator and transmission) and to a 0.45 traction coefficient.

One-lane traffic

The road is one lane wide. The ramp is split into blocks by passing bays; a block may hold trucks in only one direction. A truck asks for the next block when it is within its braking distance plus 30 m and stops in the bay niche if it is refused; loaded uphill trucks have priority, but a convoy is cut after an opposing truck has waited 90 s. Trucks in the same direction keep a headway of 1.5 s and a stopped gap of 2 m. The loader serves one truck at a time (4 bucket passes of 10 t, 36 s each), the hopper one truck at a time (45 s including the tipping), and both ends have a turning yard where trucks drive at 3 m/s.

Fuel, heat and air

Engine fuel is the wheel work divided by the driveline efficiency (0.85) and the thermal efficiency of the diesel (0.38, lower heating value 42.8 MJ/kg) plus an idle burn of 5 kg/h per engine; CO2 uses 3.16 kg per kg of diesel. The fresh-air figure uses the common design rule of about 0.06 m3/s per kW of rated diesel power; actual regulations differ by country and by engine emission class.

Simplifications

  • Straight ramp, constant grade, no curves, no gradient changes, no wet or icy spots; the road resistance is one number.
  • Four wheels, no articulation or tyre slip model; traction is a simple coefficient.
  • Bay capacity is not limited (several trucks may wait side by side); no breakdowns, shift changes, blasting or ventilation stops.
  • The speed limit, payload, loading and dumping times, retarder capacity and the 40 t truck class are typical round numbers, not the data of any vehicle or mine.
  • The traffic rules are a simple reservation scheme, not a real dispatch system; real mines also use signals and radio.

Checks in the page

The five checks compare the integrated climb with the closed-form speed, close the energy ledger, compare the simulated cycle of a lone truck with a formula, test the traffic invariant (no head-on overlap) together with Little's law at the loader yard, and compare the Blender truck with the dimensions the model uses.

Loading model...
Loading Blender model...
Distance from the loader against time, one line per truck
Tonnes per hour against the number of trucks
Speed against ramp grade
Made with 🟠 Blender · Three.js