Wankel rotary engine: trochoid housing, rotor and the 3 : 1 gearing

Blender-built hardware with a live epitrochoid housing, rotor, involute stator and ring gears, driven by the closed-cycle model of the 2D page.

Switch to 2D

Presets

Playback

Engine, fuel and speed

Camera

Layers

Quality

Model check

The science

What you are looking at

A single-rotor Wankel engine with the side plates made transparent. A triangular rotor rides on the eccentric part of the shaft; the shaft turns three times for each turn of the rotor. Three working chambers sit between the rotor flanks and the housing; the colour of each chamber is its stroke (compression, power, exhaust, intake) and its temperature. At the back, a fixed 24-tooth external gear and a 36-tooth internal gear on the rotor force the 3 : 1 ratio. Pressure, temperature and burned fraction come from the same model as the 2D page.

Geometry

In the housing frame each apex follows P(u) = R eiu + e e3iu, an epitrochoid with R = K e, e = 15 mm and width b = 70 mm. The rotor centre orbits the shaft axis on a circle of radius e at the shaft angle φ, and the rotor turns at φ/3, so the apexes are at u = φ/3 + 2πk/3. The area of a chamber between two apexes and the straight rotor flank follows from Green's theorem, A = ½[(R²+3e²)(2π/3) + 2Re(sin 2u1 − sin 2u0)] − chord term, and the swept volume is exactly Vd = 3√3 e R b.

Gears

The stator gear (24 teeth) and the rotor's internal gear (36 teeth) have the same module m = e/6 = 2.5 mm, so their pitch radii are 2e and 3e and their centres are exactly e apart, the eccentricity. A rolling ratio of 24 : 36 makes the rotor turn once while the shaft turns three times. Teeth are drawn with true involute flanks (20° pressure angle, addendum m, dedendum 1.25 m) generated in the page; the housing and rotor are generated from your K as well. The gear pair is drawn without backlash.

Thermodynamics

Each chamber goes through compression, power, exhaust and intake in 270° of shaft rotation each (1080° per chamber cycle, one firing per shaft turn for the whole rotor). The model integrates the first law, dp/dφ = −γ(p/V) dV/dφ + (γ−1)/V · dQ/dφ, with a Wiebe heat release and RK4, from the end of intake to the next volume maximum. The recess volume is set by your compression ratio, Vrecess = (Vmax − r Vmin)/(r − 1). Work per firing is ∮p dV; with an instant burn at TDC the efficiency approaches the Otto value 1 − r1−γ.

Honest simplifications

The rotor flank is drawn nearly flat (the model uses a straight chord plus a constant recess volume), the recess pocket and the leading/trailing plug ports are not drawn in detail, and there are no ports or gas exchange: the exhaust and intake strokes are shown at 1 bar. No heat transfer, friction, leakage past the apex seals or knock; constant γ = 1.35. The flame is shown only as chamber colour. The apex-seal speed is the sliding speed of an apex on the housing. The 2D page and this page label the stroke order from the same angle origin; here compression follows the volume maximum, exhaust follows the power stroke, intake precedes compression.

Checks run in the page

  • The five closed-form model checks of the 2D page (area by Green's theorem vs a 20 000-point polygon, displacement 3√3 e R b, p·Vγ constant, first-law closure, Otto limit).
  • The chamber polygon that is actually drawn (read back from the mesh) is compared with the exact area at seven shaft angles.
  • The posed apex seals (read from the scene graph after the shaft and rotor rotations) are compared with the trochoid formula at seven angles.

Credits

Blender 5.2 hardware with Cycles-baked metal textures; involute geometry and housing generated in Three.js r160. Generic design, not any manufacturer's.

Loading model...
Loading Blender model...
Chamber p-V diagram (area = work per firing)
Pressure, volume and burned fraction vs shaft angle
Apex-seal sliding speed over three shaft turns
Volume of the three chambers over three shaft turns
Made with 🟠 Blender · Three.js