Compound spur-gear train: involute teeth, DC motor and flywheel load

Two gear meshes on three shafts, drawn with true involute teeth from your tooth counts; the start-up transient is the 2D page's model.

Switch to 2D

Presets

Playback

Gears, losses and load

Camera

Layers

Quality

Model check

The science

What you are looking at

A DC motor turns pinion N₁ (steel). It drives gear N₂ (brass), which sits on the same shaft as pinion N₃ (steel); N₃ drives the output gear N₄ (bronze) and the load flywheel. All teeth are generated in the page as true involute profiles (20° pressure angle, module 2 mm, addendum m, dedendum 1.25 m) from the tooth counts you choose, and the phase of each gear is set so the teeth mesh. The start-up of the motor from rest is replayed over eight seconds; the rotation is drawn at a fraction of the real angle (see the last slider) so you can follow the teeth. Yellow and red arrows show the tangential tooth force at the two meshes.

Kinematics

For external spur gears the speed ratio of one mesh is the inverse tooth ratio, ωout/ωin = −Nin/Nout, and the sign flips at every mesh. Two stages give i = (N₂/N₁)(N₄/N₃). With ideal gears torque scales up by i and speed down by i; each real mesh transmits a fraction η, so Tout = i η² Tin. Centre distances are (N₁+N₂)m/2 and (N₃+N₄)m/2, and the tooth force at mesh 1 is F = Tmotor/r₁ with r₁ = N₁m/2.

Dynamics

Referred to the motor shaft, Jeq = Jm + Jmid/i₁² + Jload/i²: a load inertia is divided by i². The motor is T = Ts(1 − ω/ωnl) and the load (viscous c, Coulomb Tc) reflects as (cω/i + Tc)/(iη²). Then Jeq ω′ = T − Tload,refl (RK4). The steady speed is (Ts − Tc/(iη²)) / (Ts/ωnl + c/(i²η²)); for a viscous load the time constant is Jeq/(Ts/ωnl + c/(i²η²)). The last graph sweeps N₄ and shows the trade between output speed and output torque.

Contact ratio

The ideal contact ratio of a mesh is ε = [√(ra1²−rb1²) + √(ra2²−rb2²) − C sinα]/(π m cosα); above 1 means that a second pair of teeth takes the load before the first leaves contact.

Honest simplifications

Rigid shafts and teeth (no backlash or elasticity), constant mesh efficiency, an ideal DC motor, tooth forces tangential only (no radial component), no bearing or windage losses, and no undercut or profile shift: for very low tooth counts a real 20° gear would be undercut and the drawn root is only approximate. The pinion bore and lightening holes are cosmetic. The animation angle is not to scale in time; the readouts show true values.

Checks run in the page

  • The four closed-form checks of the 2D page (ratio from tooth counts, steady speed, start-up time constant, energy ledger).
  • The rendered tooth profiles of both meshes are tested at 24 phases for overlap (a point of one gear inside the other); centre distances in the scene must equal the pitch radii sums.
  • The posed gear nodes are rotated by a small angle and the overall ratio is read from their rotations and compared with (N₂/N₁)(N₄/N₃); the direction must flip at each mesh.

Credits

Blender 5.2 motor, pillars and flywheel with Cycles-baked metal textures; involute gears generated in Three.js r160.

Loading model...
Loading Blender model...
Motor and output speed during start-up
Motor torque vs reflected load torque
Power flow: input, load and mesh heat
Output speed and torque vs overall ratio
Made with 🟠 Blender · Three.js