Blast Furnace: Rist Diagram, Heat Balance and Shaft Heat Exchange

A cutaway furnace with descending coke and ore layers, rising hot gas and tapping: set coke, blast and burden and see the Rist operating line, the flame temperature and the minimum coke rate.

Switch to 2D

Presets

Playback

Parameters

Camera

Layers

Quality

Model check

The science

What is modelled

A blast furnace turns iron oxide into liquid iron with carbon from coke. Layers of coke and ore are charged at the top and sink slowly; hot air (the blast, 900 to 1300 C) is blown in near the bottom through tuyeres, burns coke to carbon monoxide and the hot gas climbs through the burden, reducing the ore and heating it. The page solves the furnace as three linked, classical balances: the mass balance with the Rist operating line, the overall heat balance, and the counter-current heat exchange in the shaft.

Equations

  • Oxygen to remove per tonne of hot metal: n_O = 1.5 n_Fe (Fe2O3 to Fe), shared between indirect reduction by CO (n_i, gives CO2) and direct reduction by carbon (n_d, gives CO).
  • Tuyere carbon C_t = C_coke - C_metal - n_d burns to CO with blast of oxygen fraction y: n_blast = 0.5 C_t / y. Top gas: CO = C_t + n_d - n_i, CO2 = n_i plus the CO2 of the limestone flux, and nitrogen.
  • Gas utilisation eta_CO = n_i / (C_t + n_d). Rist operating line: O/Fe = n_d/n_Fe + [(C_t + n_d)/n_Fe] eta. At the wuestite point (O/Fe = 1.05) the gas utilisation eta_W may not exceed the Fe/FeO/CO equilibrium eta_eq = K/(1+K), log10 K = 917/T - 1.097; the coke rate where the two meet is the minimum.
  • Heat balance per tonne: tuyere carbon to CO (110.5 MJ/kmol) plus the sensible heat of the blast equals hot metal (1300 MJ), slag, limestone calcination, losses, the endothermic direct reduction (+160 MJ/kmol O), the slightly exothermic indirect reduction (-8 MJ/kmol O) and the sensible heat of the top gas. The unknown n_d follows from this balance.
  • Raceway flame temperature: adiabatic energy balance for burning one kmol of carbon with blast and 1500 C coke, with cp = 27 + 0.0045 T J/(mol K).
  • Shaft: a two-stream counter-current exchanger, Ts' = a (Tg - Ts), Tg' = NTU (Tg - Ts), solved in closed form with the gas entering the stack at 1850 K and the charge entering at 300 K. The top-gas temperature feeds back into the heat balance, so the page iterates the two models until they agree.

Checks run in the page

  • RK4 integration of the shaft equations against the closed form.
  • Heat gained by solids equals heat lost by gas.
  • Atom balances for O, C and N.
  • Overall heat balance closure and the flame temperature enthalpy.
  • Minimum coke rate sits exactly on the equilibrium limit.
  • Blender geometry against the model dimensions, plus a volume integral.

Honest simplifications

The flame temperature ignores dissociation, moisture and injected fuel, so it comes out above the 2000 to 2300 C of real furnaces. No pulverised coal injection, no hydrogen (so the top gas has no H2 or H2O), no moisture in the blast, no carbon pick-up kinetics and no silicon or manganese chemistry beyond a fixed heat term. The shaft heat exchange uses a constant NTU and average heat capacity flows, so it cannot show the real thermal reserve zone, the cohesive zone or the gas channelling; the 1850 K belly gas temperature, the 250 MJ of losses and the 160 and -8 MJ/kmol reaction enthalpies are rounded textbook values. The Fe/FeO equilibrium fit is approximate and real furnaces run with a margin. Layers are drawn as flat slabs of conserved volume (thickness follows the taper) and are time-lapsed; gas is drawn at real speed. Educational model, not a process design tool.

What to try

  • Lower the coke rate towards the minimum and watch the W point climb onto the equilibrium line in the Rist diagram.
  • Cut the blast to 900 C: more coke has to burn for the same heat, and the flame temperature falls.
  • Enrich the blast to 30 % oxygen: less nitrogen to heat, a hotter flame and a smaller, richer top gas.
Loading model...
Loading Blender model...
Temperature of solids and gas along the stack
Rist diagram: operating line and wuestite point
Gas utilisation against coke rate
Made with 🟠 Blender · Three.js