Presets
Playback
Stimulation
Muscle
Load
Camera
Layers
Quality
Model check
The science
What is modelled
One sarcomere, the repeating contractile unit of a muscle fibre, between two Z-discs. Thick filaments of myosin hang from the M-line; thin filaments of actin (with tropomyosin and troponin) hang from the Z-discs. When calcium binds troponin, tropomyosin moves aside and myosin heads can bind actin, swing through a power stroke, detach when a new ATP binds and re-cock. The heads of the whole muscle together make the thin filaments slide towards the M-line, so the sarcomere shortens while the filaments themselves keep their length.
Equations
- Geometry (from the M-line): thick filament heads occupy
0.08 < x < 0.8 um(0.08 um bare zone, 1.6 um filament); the thin filament occupiesL/2 − 1.0 < x < L/2. The overlap length ismin(0.8, L/2) − max(0.08, L/2 − 1.0). - Active force-length:
FL = overlap / 0.72, reduced by1 − 0.97 (1 − L/2)when opposing thin filaments cross the M-line (L < 2.0 um) and tapered to zero at 1.27 um where thick filaments crumple on the Z-discs. Force reaches zero atL = 2 (0.8 + 1.0) = 3.6 um, close to the measured 3.65 um. - Passive force (titin and connective tissue):
Fp = 0.02 (e(L−2.3)/0.3 − 1)in fractions of F0 for L > 2.3 um (illustrative curve). - Calcium: each stimulus adds
q (1 − Ca), thenCadecays with τCa; activation followsAeq = Ca3/(Ca3 + 0.43)with a first-order lag τA. Steady-state peak under a pulse train of period T:c = q / (1 − (1 − q) e−T/τ), which is why a fast train fuses into a tetanus. - Hill force-velocity (shortening):
v = b (Fiso − P) / (P + a)witha = 0.25 Fisoandb = Vmax/4; the powerP vis maximal atP* = −a + √(a (a + F0)), about 0.31 F0. Lengthening is limited to0.5 Vmax. - ATP: Vmax scales with
1.05 [ATP]/([ATP] + 0.05); each cross-bridge cycle splits one ATP, and cycling rises with shortening speed (Fenn effect). With no ATP the heads that attached stay attached (rigor).
Checks run in the page
- The force-length curve from the filament geometry is compared with a head-by-head enumeration at 0.002 um spacing and with five published sliding-filament anchor points (Gordon, Huxley and Julian 1966).
- The Hill power maximum found by a numerical scan is compared with the closed form, and 20 ms of simulated isotonic shortening is compared with the analytic speed.
- The simulated calcium peak under a pulse train is compared with the closed-form steady state.
Honest simplifications
- The head poses are a schematic cycle (cocked, power stroke, hold, detach); the page does not simulate each head's chemistry stochastically. Radial distances and filament thickness are exaggerated about ten times so that the lattice is visible.
- Force and speed come from continuum (Hill) formulas, not from summing individual 3 to 5 pN head forces. Fibre-type constants (Vmax, time constants) and the passive curve are typical or illustrative, not a fit to one muscle. Specific tension 22 N/cm2 is a typical value.
- One sarcomere stands for all 4000 in series; real fibres have non-uniform sarcomeres, series elasticity in tendon and a force-dependent calcium sensitivity.
What to try
- Hold tetanus at 1.7, 2.2 and 3.2 um and watch the force follow the length-tension curve; the H zone appears above 2.0 um.
- In isotonic mode raise the load: the speed falls along the Hill curve and the power peaks near a third of the maximum force.
- Lower the stimulation frequency: single twitches stay below tetanic force until the pulses fuse. Compare a slow and a fast fibre.
- Drop ATP to zero: the heads freeze attached and the muscle cannot relax.
- Open the Fibre cutaway view to see the Blender-modelled striated myofibrils, mitochondria and sarcoplasmic reticulum.
Loading model...
Loading Blender model...