✳AEROLABINTERACTIVE ENGINEERING LIVE LAB / 001
FLIGHT SCIENCE / VIRTUAL EXPERIMENT NO. 001

Where air
becomes lift.

Step inside a precision-inspired wind tunnel. Shape the wing, change the airflow, and make the invisible forces of flight visible.

01 / 04

INTERACTIVE AERODYNAMICS
AN EXPERIMENTAL PLAYGROUND

ENTER THE WIND TUNNEL

Interactive three-dimensional wind tunnel

LIVE VISUALISATIONWIND TUNNEL // TEST SECTION A
INITIALISING
AIRFLOW DIRECTION →
SELECT A COMPONENT TO INSPECT
BUILDING THE WIND TUNNELPreparing the 3D environment…
LIFT FORCE 01
3.99 kN
PERPENDICULAR TO THE FREESTREAM
DRAG FORCE 02
287 N
OPPOSES THE AIRFLOW
LIFT COEFFICIENT 03
0.692 CL
DIMENSIONLESS AERODYNAMIC RESPONSE
DYNAMIC PRESSURE 04
480 Pa
½ × AIR DENSITY × VELOCITY²
REAL-TIME AERODYNAMIC RESPONSE

Lift coefficient vs. angle

ATTACHED FLOW / APPROX.
−10° ANGLE OF ATTACK24° ANGLE OF ATTACK
THE FUNDAMENTAL RELATIONSHIPS

Air in motion.
Forces in numbers.

L = ½ ρV²SCL
D = ½ ρV²SCD

Wing reference area: 12 m². Aspect ratio: 7.0. These are transparent, illustrative equations and coefficients, not measured or certified flight data.

EST. DRAG COEFFICIENT0.0499

About This 3D Simulation

What really changes when you tilt a wing into the wind?

This interactive wind tunnel invites you into the test section of an imaginary aerospace laboratory. At its centre is a three-dimensional wing built from a four-digit NACA airfoil profile, suspended between engineering fixtures and surrounded by a transparent enclosure. An inlet fan, support structure, metallic surfaces, instrument probes, and moving airflow traces establish the visual language of an authentic research facility. The scene is procedurally constructed in the browser with Three.js; no pre-rendered film or fixed animation substitutes for your input.

Start with the NACA 2412, then compare it with the symmetrical NACA 0012 or more highly cambered NACA 4412. The selectable wing contour is rebuilt in real time. Adjust the geometric angle of attack, lower the trailing-edge flap, or change the wind velocity and density. The wind tunnel responds instantly: the model reorients, the flap rotates, the fan and flow markers change pace, and the live aerodynamic calculations are recomputed.

The four large instruments display lift, drag, lift coefficient, and dynamic pressure. A separate coefficient plot traces the model's characteristic rise toward stall and subsequent decline. Optional surface colours provide a qualitative impression of pressure differences, while force vectors translate numerical results into spatial directions. The inspection view opens one side of the tunnel for a less obstructed look at the test wing.

For engineers, students, educators, and curious visitors, the experiment illustrates the balance between wing geometry, operating conditions, and aerodynamic response. It offers a practical bridge between introductory formulas and the physical design of a lifting surface. You can investigate why increased airspeed has a quadratic effect on force, why flaps change both lift and drag, and why a high angle of attack does not indefinitely increase lift.

This is a high-quality educational visualisation with a deliberately simplified aerodynamic model, not a full computational-fluid-dynamics solver or a source of certified aircraft performance data. The animated flow and surface colours communicate concepts rather than measured pressure or velocity fields. This distinction is part of the lesson: sophisticated-looking graphics do not replace validation. Experiment freely, compare trends, and use the visible equations to understand exactly what the tool does—and does not—calculate.

How It Works

From airfoil geometry to the forces that keep aircraft aloft.

1. Shape a real family of airfoils

The 3D wing begins with the NACA four-digit geometry system. In a designation such as 2412, the first digit represents maximum camber as a percentage of chord, the second digit indicates the camber location in tenths of chord, and the final two digits express maximum thickness as a percentage of chord. A standard thickness distribution and piecewise camber line determine upper and lower surface coordinates. Our geometry generator lofts these sections across a finite span, adds a slightly tapered tip, and builds a separate trailing-edge flap that can rotate.

2. Turn wind into measurable pressure

Dynamic pressure connects air density and speed: q = ½ρV². In the model, density is adjustable and speed ranges from 10 to 75 metres per second. For example, at 28 m/s with density 1.225 kg/m³, dynamic pressure is approximately 480 pascals. Doubling speed would produce four times the dynamic pressure if density remained constant. The fan and moving particles visualise your speed setting, but they are not solving a pressure field through the tunnel.

3. Estimate wing lift and drag

The estimated lift is L = qSCL, and estimated drag is D = qSCD, using a reference area S of 12 m². A simplified finite-wing lift slope makes CL vary approximately linearly with angle of attack. Different airfoil camber settings introduce small lift offsets. Positive flap deflection increases the effective angle in the coefficient model, while also adding drag. The coefficients are illustrative and remain dimensionless.

4. Explore the stall boundary

Real wings cannot continue increasing lift indefinitely with angle. At sufficiently high incidence, boundary-layer separation weakens the normal lift trend and increases drag. This demonstration applies a smooth post-stall adjustment at high effective incidence. The exact turning point is an intentionally approximate teaching parameter rather than a validated stall angle for any real wing. In the near-stall preset, the changing coefficient curve makes the underlying trade-off especially easy to see.

5. Understand induced drag

Because a wing has a finite span, lift comes with an additional induced-drag cost. Our model adds a term proportional to CL² / (πeAR), where the assumed aspect ratio AR is 7.0 and the efficiency factor e is 0.82. A baseline profile drag and flap penalty complete the estimate. This is a compact engineering-style drag polar, not a comprehensive representation of skin friction, compressibility, turbulence, or three-dimensional vortex dynamics.

6. See the calculations in three dimensions

When a slider changes, the browser recomputes the forces, updates the numeric instruments and coefficient graph, rotates the wing or flap where appropriate, and adjusts illustrative streamlines. A vertical arrow represents lift, while a horizontal arrow points in the drag direction. Their lengths scale to show relative changes, but are capped for legibility. The pressure-colour option is a qualitative visual guide rather than a pressure-tap measurement. Clicking the wing, fan, or tunnel reveals a component label.

7. Relate the experiment to aircraft design

Aircraft designers use wind tunnels, numerical analysis, and flight tests to understand aerodynamic performance across operating conditions. Airfoil camber, flap geometry, wing aspect ratio, angle of attack, and freestream conditions all influence the resulting forces. The same basic force relationships can introduce questions about lift-to-drag ratio, approach speed, stall, and energy efficiency. This digital exhibit is best used to build intuition before moving to higher-fidelity methods. It intentionally omits Mach-number corrections, Reynolds-number dependence, detailed wall interference, unsteady flow, and flight dynamics, so it cannot determine whether a real aircraft is safe to fly.

FIELD MANUAL / 01

How to Use This Simulation

Five quick ways to investigate a wing in controlled airflow.

  1. 01Explore the 3D scene

    Drag on the model to orbit. Scroll, pinch, or use +/− to zoom. Select an object to learn what it represents, or reset the camera to its original angle.

  2. 02Set a flight condition

    Choose a Cruise, Approach, or Near Stall preset. Adjust wind speed, air density, angle of attack, flap deflection, and airfoil geometry individually.

  3. 03Read the instruments

    Compare lift, drag, lift coefficient, and dynamic pressure. Follow the lift curve to see how incidence changes the simplified aerodynamic response.

  4. 04Change the visual layers

    Turn airflow, pressure colours, and force arrows on or off. Enable inspection view to hide one transparent wall and reveal the wing more clearly.

  5. 05Run a small experiment

    Keep everything fixed, double the wind speed, and compare forces. Then apply positive flap and observe the changed lift and drag. Pause or reset at any time.

Frequently Asked
Questions

Explore the engineering behind the model, its scientific assumptions, and what it can teach us about real aircraft.

What does a wind tunnel reveal about an aircraft wing?

A wind tunnel allows researchers to observe how controlled airflow interacts with a wing or another test article. Engineers measure aerodynamic forces, pressure distributions, and changes in flow behaviour while adjusting variables such as airspeed and angle of attack. In this interactive model, a NACA-style wing sits inside a transparent test section, surrounded by illustrative streamlines and live force indicators. You can change the wind speed, air density, wing profile, angle of attack, and flap deflection. The resulting lift and drag estimates update immediately. Unlike a laboratory wind tunnel, this browser experience does not solve the full Navier–Stokes equations or reproduce turbulent flow in three dimensions. It is an educational tool for understanding relationships, testing intuition, and exploring how wing geometry influences flight performance.

How does an airfoil generate lift in moving air?

A wing redirects air and establishes a pressure distribution around its surfaces. The combined pressure and shear stresses create a net aerodynamic force, typically resolved into lift perpendicular to the freestream and drag parallel to it. Camber and angle of attack influence circulation and therefore the amount of lift generated. The interaction is not explained by a rule that air parcels must meet again at the trailing edge; that common explanation is incorrect. In this simulation, a finite-wing lift slope provides a simplified estimate of lift coefficient. The model also applies a soft stall adjustment at higher angles. Airflow paths are conceptual illustrations rather than a computed velocity field. Watch the force arrows and coefficient plot as you adjust the wing's orientation to see the overall trend.

What is the difference between NACA 0012, 2412, and 4412?

These three familiar four-digit NACA profiles share a nominal maximum thickness of 12 percent of chord but have different camber. NACA 0012 is symmetrical, with zero design camber; at zero angle of attack its idealised lift is approximately zero. NACA 2412 has 2 percent maximum camber at 40 percent chord, giving it positive lift at a small geometric angle. NACA 4412 has 4 percent maximum camber at the same chord location and generally exhibits a stronger positive lift tendency in this simplified comparison. Real aerodynamic characteristics depend on Reynolds number, wing planform, surface condition, and test setup. Switching profiles here rebuilds the 3D wing contour and changes the approximate zero-angle lift offset, allowing direct visual and numerical comparison.

What happens when the angle of attack becomes too high?

At modest angles of attack, lift usually increases approximately linearly with angle. As the angle rises, the pressure gradient along the wing's upper surface becomes harder for the boundary layer to follow. Eventually substantial flow separation can occur, reducing the lift coefficient and increasing drag. This behaviour is commonly called stall; it is not the same as an engine stopping or the aircraft losing all airflow. Our model uses a smooth, deliberately approximate stall curve rather than computational fluid dynamics. Its exact stall threshold is not suitable for aircraft design, certification, or operational decisions. Move the angle slider toward the high end and note how lift growth slows or reverses while drag climbs and the status indicator changes.

Why does increasing wind speed have such a large effect on forces?

Aerodynamic force depends on dynamic pressure, defined as one half of air density multiplied by the square of airspeed. Lift is dynamic pressure multiplied by reference wing area and lift coefficient; drag uses the drag coefficient instead. If you double the speed while holding the other inputs and coefficients constant, calculated lift and drag become approximately four times larger. This quadratic relationship is one reason why relatively small changes in speed can be aerodynamically significant. The simulation displays speed in metres per second and estimated force in newtons or kilonewtons. Changes in speed animate the illustrative flow particles and intake fan as well. In real flows, changing speed can also alter Reynolds number and aerodynamic coefficients, which this model does not fully capture.

How do trailing-edge flaps influence lift and drag?

Lowering a trailing-edge flap changes the local camber and the direction in which the wing deflects the airflow. Within useful operating ranges, positive flap deflection tends to increase lift at a given geometric angle of attack, but it also increases profile drag. Flaps are particularly useful during take-off and landing when extra lift at lower flight speeds can be valuable. This 3D demonstration rotates a distinct trailing-edge flap and approximates its contribution through an effective lift-angle increment and drag penalty. It does not model a slot, hinge gap, unsteady separation, or complex high-lift system aerodynamics. Compare the Cruise and Approach presets to see how a positive flap setting changes both coefficients and the estimated forces.

How are lift, drag, and dynamic pressure calculated here?

The core relationships are q = ½ρV², L = qSCL, and D = qSCD. Here q is dynamic pressure, ρ is air density, V is freestream speed, S is the selected reference area, and CL and CD are dimensionless aerodynamic coefficients. The model uses an illustrative finite-wing lift slope, profile-specific camber offsets, a simplified high-angle stall correction, and an induced-drag contribution that grows with the square of lift coefficient. A flap penalty adds extra drag when the control surface is deflected. The fixed reference area is 12 square metres and the assumed aspect ratio is 7.0. These inputs yield internally consistent educational estimates, not measured wind-tunnel data. Real aircraft analysis needs calibrated aerodynamic polars and validated models.

Can this model predict the performance of a real aircraft?

No. This demonstration is intended for exploration and teaching, not aerodynamic design or safety-critical decision-making. An actual aircraft wing has a specific span, sweep, taper, twist, surface finish, high-lift geometry, fuselage interaction, and often compressibility effects. Its aerodynamic coefficients also vary with Reynolds number and sometimes with Mach number. Our 3D geometry represents a simplified finite-span airfoil, while the force calculations use a compact analytic approximation rather than pressure integration over a solved flow field. The streamlines are designed to help visual interpretation, not to claim a high-fidelity prediction of vortices or turbulence. Use the tool to learn directions and relative sensitivities; use validated experiments, CFD, or engineering references for real performance estimates.

What do the coloured wing surface and airflow lines represent?

The optional pressure view uses a qualitative colour treatment to help distinguish regions that tend to contribute differently to lift. Cool colours indicate a lower-pressure tendency over much of the upper surface, while warm colours indicate a relatively higher-pressure tendency below. They are not calibrated pressure coefficients and should not be read as experimental measurements. The animated lines trace a stylised, smooth flow pattern around the airfoil. They make speed and downwash easier to visualise, but they do not reproduce a true viscous wake, boundary layer, or three-dimensional tip-vortex system. For a clearer mechanical inspection, turn the flow paths off. Switch force vectors on to see the approximate directions of the total lift and drag forces.

Why do wingtip vortices and induced drag matter?

A finite wing has a pressure difference between its lower and upper surfaces. Near the wingtips, the resulting three-dimensional flow contributes to trailing vorticity and a downwash field behind the wing. The wing's effective aerodynamic force is tilted backward slightly, producing induced drag. In many simplified models, the induced drag coefficient is approximately CL² divided by π times aspect ratio times an efficiency factor. Therefore high-lift conditions often bring a meaningful drag cost, even if the airfoil's profile drag were unchanged. Aspect ratio, lift distribution, and wingtip design influence the effect in practice. This model includes an illustrative induced-drag term in the live calculation, but does not numerically resolve vortices. The surrounding lines communicate only a conceptual downwash pattern.

Made with 🤖 ChatGPT · Three.js